686039
12
Zoom out
Zoom in
Previous page
1/21
Next page
254
A
S AVE THESE INSTRUCTIONS
(254IO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 01/28/2016
English
Page 12
OPERATION
SPA CONTROL UNIT PANEL
On/Off Button: Once the unit is plugged in, use this button to active the control unit panel
buttons. The light next to the button is green when activated. Press this button to turn off all
currently activated functions.
NOTE: The On/Off button may appear as a black button in the center of the control panel.
Heat Button: Use this button to activate the heating system. The pump will heat the spa water
until the water temperature reaches the set temperature. When the spa water temperature drops
1-2°C (1.8-3.6°F) below the set temperature the heating system will restart. When the ame icon
on the display is red, the heating system is activated. When the ame icon turns green, the
water is at the set temperature. The heating system is at rest and the ltration system will
continue working nonstop.
NOTE: To stop the ltration system while the heater is at rest mode, press the ame button rst
and then the lter button. Pressing the ame button only while the heater is at rest mode will
turn off the heating system only and the ltration system will operate for another 24 hours before
it turns off automatically.
Celsius/Fahrenheit Toggle button:
The temperature can be displayed in either Fahrenheit or Celsius. The system’s default is
Celsius.
CAUTION: NEVER use the spa if indicated water temperature is more than 40°C (104ºF).
Temperature Adjustment Buttons: Pressing the Temperature Increase or Decrease
buttons will cause the LED to ash. When ashing you can adjust to the desired temperature
setting. If you hold these buttons down the values will rapidly increase or decrease. The new
and desired temperature setting will remain on the LED display for 5 seconds to con rm the new
value.
NOTE: The default temperature is 20°C (68°F).
NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Water Filter Button:
This button turns the lter pump on and off. If the heating system is activated the ltration
system will automatically start.
The water lter icon on the display is green when activated.
Bubble Button: Use this button to activate the massage system, which has a 30-minute
auto-shutoff feature. The bubble icon on the displays is green when activated.
WARNING: Do not run Bubble system when the cover is attached, air can accumulate
inside the spa and cause irreparable damage and bodily harm.
LED Display: Once plugged in the LED displays the current water temperature automatically.
NOTE: the built-in hard water treatment function works automatically in conjunction with the ltration system.
IMPORTANT: The following conditions will lead to slow water heating.
• The ambient temperature is lower than 10ºC (50ºF).
• Outdoor wind speed is above 3.5-5.4m/s (8-12 mph).
• The air bubble function is activated when heating the spa water.
• The spa is not properly covered with the spa cover when the water is heating.
A: Heat Button
B: Celsius/Fahrenheit Toggle Button
C: Temperature Increase Button
D: Temperature Decrease Button
E: Water Filter Button
F: Bubble Button
G: LED Display
H: On/Off Button
40 C
o
F
E
DC
B
A
G
H
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex PureSpa - 28474 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex PureSpa - 28474 in the language / languages: English as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex PureSpa - 28474

Intex PureSpa - 28474 User Manual - German - 24 pages

Intex PureSpa - 28474 User Manual - Dutch - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info