686082
16
Zoom out
Zoom in
Previous page
1/18
Next page
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
English
OWNER’S MANUAL
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change specifications and appearance, which may result
in updates to the instruction manual, without notice
.
For illustrative purposes only.
©2012 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte
vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/
Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in
Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex
Recreation Corp., P.O. Box 1440, Long Beach, CA 90801Distributed in the European Union by/Distribué dans l’Union Européenne
par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., Venneveld 9, 4705 RR
Roosendaal – The Netherlands
Krystal Clear™
Model 634T Filter Pump
220 - 240 V~, 50 Hz, 360 W
Hmax 1.5 m, H min 0.19 m, IPX4
Max. Water Temperature 35 °C
110-*A*-R1-1308
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 2
English
TABLE OF CONTENTS
Warnings.......................................................................... 3
Parts List & Reference.................................................... 4-6
Setup Instructions........................................................... 7-10
Operating Instructions.................................................... 11
Operating Time Table...................................................... 12
Maintenance..................................................................... 13-14
Pool Care and Chemicals............................................... 13
Long Term Storage.......................................................... 14
Troubleshooting Guide................................................... 15
Common Pool Problems................................................. 16
General Aquatic Safety................................................... 17
Limited Warranty.............................................................. 18
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 3
English
SAFETY RULES
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
• To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
Children should be supervised to ensure that they do not play with the appliance.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge. They
must at all times be supervised by a knowledgeable and experienced adult
responsible for their safety.
• Assembly and disassembly by adults only.
• Risk of electric shock. Connect this product only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device
(RCD). Contact a qualified electrician if you cannot verify that the receptacle is
protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,
which has a maximum rate of 30mA. Do not use a portable residual current device
(PRCD).
• Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
The plug must be accessible after produc t is installed.
Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
Keep this product more than 2m away from the pool.
Keep this product more than 3.5m away from the pool (for France only).
• Keep the plug of this product more than 3.5m away from the pool.
• Position this product away from the pool, so as to prevent children from climbing on
it and accessing the pool.
• Do not operate this product when pool is occupied.
• This product is for use with storable pools only. Do not use with permanently
installed pools. A storable pool is constructed so that it may be readily
disassembled for storage and reassembled to its original configuration.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 4
English
PARTS LIST
PARTS LIST
1
9
4 5
10
13 14 15
2
11 12
6
3
87
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 5
English
PARTS REFERENCE
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
When ordering parts, be sure to quote the model number and part numbers.
1
2
3
4
5
6
7
8
REF. NO.
DESCRIPTION
QTY.
SPARE PART NO.
1
2
2
1
1
1
1
2
THREADED FILTER HOUSING COLLAR
AIR RELEASE VALVE/SEDIMENT RELEASE VALVE
VALVE O-RING
FILTER HOUSING COVER
FILTER HOUSING O-RING
FILTER CARTRIDGE (59905)
AIR RELEASE VALVE B (WITH O-RING)
PUMP HOSE WITH NUTS
10491
10460
10264
10490
10492
10725
11010
2
3
4
5
1
6
3
7
2
8
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 6
English
PARTS REFERENCE
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
9
10
11 12 13 14 15
9
10
11 12 13 14
9
10
11
12
13
14
15
REF. NO.
DESCRIPTION
QTY.
SPARE PART NO.
2
2
2
2
1
10747
10262
10745
10256
10255
11235
11074
When ordering parts, be sure to quote the model number and part numbers.
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)
HOSE O-RING
STEP WASHER
STRAINER NUT
FLAT STRAINER RUBBER WASHER
THREADED STRAINER CONNECTOR
ADJUSTABLE POOL INLET NOZZLE
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 7
English
SETUP INSTRUCTIONS
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (14) (see drawing 1). Be
careful not to lose the step rubber
washer (11). Place the plunger valve on the
ground in a safe place.
2. In a counter-clockwise motion unscrew
the strainer nut (12) from the threaded
connector (14). Leave the flat washer (13)
on the connector (14).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked"+").
From the inside of the pool liner insert
the connector (14) into one of the pre-cut
holes with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side of
the strainer nut (12) facing the outside wall
of the liner in a clockwise motion screw the
strainer nut (12) back onto the threaded
connector (14) (see drawing 2).
5. Finger tighten the strainer nut (12) onto the
threaded connector (14).
6. Grasp the plunger valve assembly. Make
sure the step washer (11) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (14) (see drawing 3).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during
filling of the pool (see drawing 4).
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. The plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. If your pool
has inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The parts numbers here onward, refer to the
parts depicted in the Parts List section of this manual. To install, do the
following:
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP
13 14
2
INSIDE
LINER WALL
12
1
2
1
3
1
2
4
INSIDE
LINER WALL
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 8
English
SETUP INSTRUCTIONS
POOL INLET - NOZZLE & PLUNGER VALVE SETUP
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (14) (see drawing 5).
Be careful not to lose the step rubber
washer (11). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew
the strainer nut (12) from the threaded
connector (14). Leave the flat
washer (13) on the connector (14).
3. Install the nozzle and plunger valve at the
upper position of the pool inlet. From the
inside of the pool liner insert the
connector (14) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side of
the strainer nut (12) facing the outside wall
of the liner in a clockwise motion screw the
strainer nut (12) back onto the threaded
connector (14) (see drawing 6).
5. Finger tighten the adjustable pool inlet
nozzle (15) and the strainer nut (12) onto
the threaded connector (14).
6. Grasp the plunger valve assembly. Make
sure the step washer (11) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (14) (see drawing 7).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during
filling of the pool (see drawing 8).
9. Adjust the direction of the nozzle head
pointing away from the pool outlet for a
better circulation result (see drawing 9).
10. The pool liner is now ready to be filled with
water. Consult the above-ground-pool
owner’s manual for the filling instructions.
5
1
7
1
2
6
13 14
15
INSIDE
LINER WALL
12
2
8
INSIDE
LINER WALL
9
Pool
WATER
FLOW
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 9
English
SETUP INSTRUCTIONS
FILTER PUMP HOSE CONNECTION SETUP
1. Remove the Krystal Clear™ filter pump and hoses from the packaging.
2. Place the filter pump in such a manner, that you can easily assemble the
hose (8) connections to the plunger valve.
Note: Some regional regulations may require the filter pump to be
mounted on a stationary platform. There are two mounting holes located
in the pump base for this reason. Consult your local authorities for
filter-pump mounting requirements.
3. Grasp the two pump hoses (8) and connect the hose nuts to the filter pump.
4. In a counter-clockwise motion unscrew the threaded filter housing collar (1)
from the filter housing. Place it in a safe place.
5. The Filter Pump is an airtight system. In a counter-clockwise motion turn both
air release valves (2 & 7) 1 - 2 turns to open. DO NOT remove air release
valves as water will expel with force if the motor is turned on and injury
may occur.
6. Grasp and remove the filter housing cover (4). Check to see if a cartridge is
i
nside the housing. If yes, replace the cover, finger tighten the housing collar (1)
back onto the filter housing.
7. Gently finger tighten the sediment release valve located at the bottom of the
housing to be sure that water does not leak out.
8. When the pool is filled connect the hose from the bottom of the filter housing to
the highest strainer assembly. You will find the hose connection at the bottom
of the plunger valve assembly. Use the hose nut to attach the hose.
9. Connect the second hose which is fixed to the middle of the motor housing to
the remaining liner connection.
WARNING
Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
The installation instruction shall provide information on requirements specified for
the electrical installation and shall include reference to national wiring rules.
WATER LEVEL
ADJUSTABLE POOL
INLET NOZZLE
PLUNGER VALVE
ASSEMBLY
HOSE NUT
OUTLET HOSE
INSIDE LINER
WALL
THREADED
STRAINER
CONNECTOR
FILTER HOUSING
COLLAR
FILTER CARTRIDGE
INSIDE
FILTER HOUSING
COVER
AIR RELEASE
VALVE
MOTOR
HOUSING
HOSE O-RING
POWER CORD
INLET HOSE
OUTSIDE
LINER WALL
(ILLUSTRATION NOT TO SCALE)
W
A
T
E
R
F
L
O
W
W
A
T
E
R
F
L
O
W
HOSE O-RING
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 10
English
SETUP INSTRUCTIONS
FILTER PUMP STATIONARY MOUNTING
Some countries, especially in the European community, require the filter-pump to
be secured to the ground or to a base in a permanent upright position. Check your
local authorities to determine if there is a regulation in your area regarding
above-the-ground swimming pool filter-pumps. If yes, then the filter-pump can be
mounted to a platform using the two holes located in the base. See drawing below.
The filter-pump can be mounted on a cement base or onto a wooden platform to
prevent accidental falling over. Total assembly must exceed 18kg.
165 mm
1. The mounting holes are 6.4 mm in diameter and spaced 165 mm apart.
2. Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
FILTER PUMP INSTALLATION DISTANCE
(Generic layout of an electrical device relative to a swimming pool. Illustration not to
scale)
According to the International Standard, IEC 60364-7-702, on electrical installation
of swimming pools and other basins equipments, the following installation distances
must be respected:
The filter pump must be position more than 2m away from the pool walls.
The power cord plug to the 220-240 volt electrical power source of the filter
pump must be position more than 3.5 m away from the pool walls.
Check your local authorities to determine the appropriate standard and
requirements for “electrical installation of swimming pools and basins equipments”.
The following table is for reference only:
International
France
Germany
The Netherlands
Country/Region
Standard Number
IEC 60364-7-702
NF C 15-100-7-702
DIN VDE 0100-702
NEN 1010-702
>2m
>3.5m
POOL
hoses
Electrical
device
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 11
English
OPERATING INSTRUCTIONS
1. Make sure the filter pump is switched off. The switch is located on the motor
housing.
2. Connect the power cord to a GFCI protected electrical outlet.
3. Turn both plunger valve handles fully counter-clockwise until they stop. This
opens the valve, allowing water to flow into the filter pump.
4. With water flowing into filter pump, the water pressure will allow the air trapped
inside to escape from the air release valves (2 & 7). When all the air has
escaped water will flow out of the valves (2 & 7). When this occurs gently
finger tighten the valves (2 & 7) in a clockwise direction.
5. To operate the filter pump on “TIMER” mode:
A. Set the timer dial to the desired operating hours. See operation time table.
See Fig. 10
B. Turn on the pump by pressing the switch to ” position, the filter pump is
now filtering the water and will stop after the operating hours are
completed. The built-in timer will now operate for the number of hours
selected at the same time each day.
C. Operating hours can be re-adjusted if necessary. Follow step A – B.
To operate the filter pump manually (without the “TIMER” mode):
A. Turn on the pump by pressing the switch to “I” position, the filter pump is
now filtering the water.
B. To turn off the pump, press the switch to “O” position.
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open the air
release valves, wait until water starts to flow out of the air release valves,
close air release valves.
IMPORTANT
OPERATING INSTRUCTIONS
Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or residual
current device (RCD). Contact a qualified electrician if you cannot verify
that the receptacle is protected by a GFCI/RCD. Use a qualified electrician
to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a
portable residual current device (PRCD).
WARNING
FIG 10
ON
OFF
TIMER
TIMER DIAL (HOURS)
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 12
English
OPERATING TIME TABLE
This table shows the required operating time for average use of the filter pump with AGP's.
The filter pump running time should be 1 hour longer than the required operating time of the
Saltwater System.
Pool Size
Water Capacity (Calculated at 90% for Frame
Pool and 80% for Easy Set & Oval Pool)
Recommend
operating hours
per day
(Gals)
(Liters) (Hours)
INTEX ABOVE GROUND P OOLS (AGP’s)
EASY SET
®
POOL
18’ x 42” (549cm x 107cm)
4,786 18,115 4
18’ x 48” (549cm x 122cm)
5,455 20,647 4
CIRCULAR
METAL FRAME
POOL
18’ x 48” (549cm x 122cm)
6,423 24,311 4
24’ x 52” (732cm x 132cm)
12,481 47,241 6
ULTRA FRAME
POOL
16' x 48" (488cm x 122cm)
5,061 19,156
4
18’ x 48” (549cm x 122cm)
6,423 24,311 4
18’ x 52” (549cm x 132cm)
6,981 26,423 4
20’ x 48”
7,947 30,079 4
22’ x 52” (671cm x 132cm)
10,472 39,637 6
24'x52"
12,481 47,241 6
26’ x 52” (792cm x 132cm)
14,667 55,515 8
SEQUOIA SPIRIT
®
POOL SET
15’8” x 49”
4,440 16,805 4
16'8" x 49" (508cm x 124cm)
5,061 19,156 4
18'8" x 53" (569cm x 135cm)
6,981 26,423 4
OVAL FRAME
POOL
20’ x 12’ x 48” (610cm x 366cm x 122cm)
4,393 16,628 4
RECT. ULTRA
FRAME POOL
15’ x 9’ x 48”
3,484 13,187 2
18’ x 9’ x 52” (549cm x 274cm x 132cm)
4,545 17,203 4
20’ x 10 x 52”
5,611 21,238 4
24’ x 12’ x 52” (732cm x 366cm x 132cm)
8,403 31,805 4
32’ x 16’ x 52” (975cm x 488cm x 132cm)
14,364 54,368 8
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 13
English
MAINTENANCE
POOL CARE AND CHEMICALS
CLEANING OR REPLACING FILTER CARTRIDGES
All pools require care to keep the water clear and hygienically clean. With
proper chemical control, your filter will help attain this objective. Consult your
pool supply dealer for instructions regarding the proper use of chlorine,
algaecide and other chemical agents required for sparkling clear water.
Keep pool chemicals away from children.
Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations
could occur.
Daily pH checking and chemical treatment of the water is very important and
can not be overemphasized. Chlorine, algaecide and maintenance of proper pH
levels are required when filling the pool as well as during the season. Consult
your local swimming pool supply store for instructions.
The season's first filling of the pool may have brackish water requiring extra
water additives and extra filter changes. Do not allow swimming in pool until the
pH level is balanced. Consult your local swimming pool supply store for
instructions.
Keep spare filter cartridges on hand. Replace cartridges every two weeks.
Chlorinated water may damage lawns, gardens or shrubbery as children play
in the pool and splash water outside the pool. Lawn areas underneath the
pool liner will be destroyed. Note that some types of grass may grow through
the liner.
Filter run time depends on pool size, weather and usage level. Experiment with
various run times so as to produce clean clear water.
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always
follow the chemical manufacturer’s directions, and the health and hazard
warnings.
It is recommended that the filter cartridge be replaced at least
every 2 weeks.
1. Make sure the filter pump is turned off, then disconnect the power cord from
the electrical outlet.
2. Turn both plunger valve handles fully clockwise until they stop. This closes the
valve, prevents the water from flowing out of the pool.
3. Gently turn the top air release valve once or twice in a counter-clockwise
direction. The housing cover can now be easily removed.
4. In a counter-clockwise direction remove the filter housing collar (1). Place it in
a safe location.
5. Remove the housing cover (4).
6. Now remove the used filter cartridge.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 14
English
MAINTENANCE
1. Before emptying your pool for long term storage, or relocation, be sure the
water is directed towards an acceptable drain water receptacle away from the
house. Check local regulations for specific directions regarding disposal of
swimming pool water.
2. Disconnect power cord from electrical outlet.
3. Now, drain the pool.
4. When the pool is empty, disconnect all hoses from pump and plunger valves
and remove the strainers from the pool wall.
5. Drain all water from the filter pump.
6. Leave filter pump pieces & hoses outside to thoroughly air dry.
7. Remove both plunger valves from the threaded strainer connector (14). Be careful
not to lose the step rubber washer (11).
8. Coat the following O-rings and washers with petroleum jelly for long term
storage:
Air release valve & sediment O-rings (3).
Filter housing cover O-ring (5).
Pump hose O-rings (10).
Strainer valve assembly step washers (11).
Flat strainer rubber washers (13).
9. Discard the used filter cartridge. Put aside 1 or 2 new cartridges for next
season’s use.
10. It is best to place all dry pieces in the original packaging for storage or place
them in an airtight plastic bag.
11. Store the unit and accessories in a dry place. The storage's temperature
should be controlled, between 32 degrees Fahrenheit (0 degrees Celsius) and
104 degrees Fahrenheit (40 degrees Celsius) storage location.
LONG TERM STORAGE
CLEANING OR REPLACING FILTER CARTRIDGES (continued)
7. Examine the inside of the filter housing.
8. If dirt or sediment is located on the bottom of the housing then:
A. In a counter-clockwise motion gently unscrew and remove the sediment
valve (2) located at the bottom of the housing. Place it in a safe place.
B. With a bucket of water or a garden hose pour water into the housing
flushing out the sediment.
C. Screw back the sediment valve (2) in a gentle clockwise motion. Do not
over-tighten.
9. Place a new cartridge filter in the housing.
10. Return the housing cover (4) to its position and in a clockwise direction rescrew
the housing collar (1) onto the filter housing.
11. Turn both plunger valve handles fully counter-clockwise until they stop. This
opens the valve, allowing water to flow into the filter pump.
12. When the trapped air has escaped through the air release valve gently
retighten the valve (2) in a clockwise direction.
13. Reconnect the power cord.
14. Turn on the pump.
IMPORTANT
It is best to store away your poolsystem in its original packaging.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 15
English
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T
PUMP WATER OR
THE WATER FLOW
IS VERY SLOW
PUMP DOESN’T
WORK
TOP COVER
LEAKING
HOSE LEAKING
AIR LOCK
The motor is not plugged in.
The Fuse box needs checking.
The GFCI/RCD circuit breaker
is tripped.
Motor too hot and overload
protection is shut off.
Improper chlorine or pH
levels.
Filter cartridge is dirty.
Damaged cartridge.
Excessively dirty pool.
The strainer screen is
restricting the water flow.
Clogged inlet or discharge.
An air leak on the intake line.
Scale or buildup on cartridge.
Excessively dirty pool.
Dirty filter cartridge.
The nozzle and strainer
connection are reversed.
Low water level.
Strainer screen plugged up.
An air leak on the intake hose.
Faulty motor or the impeller
is jammed.
An air lock inside the cartridge
chamber.
O-ring missing.
Cover is not tight.
Filter cartridge is dirty.
Hose nuts are not well-fitted.
There’s air trapped in the
pump housing and inlet hose.
The inlet and outlet hoses
connection are reversed.
TROUBLE CAUSE SOLUTION
Filter cord must be plugged into a 3
wire outlet that is protected by a Class
A Ground Fault Circuit Interrupter, or
RCD.
Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
Let the motor cool down.
Adjust the chlorine and pH level. Consult
your local swimming pool supply stores.
Clean or replace cartridge.
Check the cartridge for holes. Replace
if damaged.
Operate the filter for longer periods.
Clean the strainer screen at the inlet.
Clear any obstructions in the intake
hose by discharging it inside pool wall.
Tighten hose nuts, check hoses for
damage, check pool water level.
Replace cartridge.
Clean cartridge more often.
Clean inside the plunger valve.
Pull valve handle to full upright position.
Install the nozzle at the upper position
of pool inlet, and the strainer at the
lower position of pool outlet.
Fill pool to correct water level.
Clean strainer screens at pool inlet.
Tighten hose nuts, check hose for
damage.
Clear any sticks or leaves in the
intake hose.
Turn and pull valve handle to full upright
position.
Remove cover & check for O-ring.
Tighten cover (Manually).
Replace or clean cartridge.
Tighten or reinstall hose nut.
Open air release valves, wait until water
starts to flow out of the valves, then
close it.
The lower position of pool outlet
connects to filter pump water inlet. The
upper position of pool inlet connects to
filter pump water outlet.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 16
English
COMMON POOL PROBLEMS
COMMON PROBLEMS
PROBLEM DESCRIPTION CAUSE SOLUTION
ALGAE
COLORED
WATER
FLOATING
MATTER IN
WATER
CHRONIC
LOW WATER
LEVEL
SEDIMENT
ON POOL
BOTTOM
SURFACE
DEBRIS
• Chlorine and pH levels
need adjustment.
• Copper, iron or
manganese in water
being oxidized by the
added chlorine.
This is Common.
• "Hard water" caused
by a too high pH level.
• Chlorine content is low.
• Foreign matter in
water.
• Rip or hole in pool
liner or hoses.
• The drain valves are
loose.
• Heavy use, getting in
and out of pool.
• Pool too close to
trees.
Super chlorinate with shock
treatment. Correct pH to your
pool store's recommended
level.
Vacuum pool bottom.
Maintain proper chlorine
level.
Adjust pH level to the
recommended level.
Run filter until water is clear.
Clean cartridge frequently.
Correct the pH level. Check
with your pool dealer for
advice.
Adjust the chlorine level.
Clean or replace your filter.
Repair with a patch kit.
Finger tighten all caps.
Use Intex pool vacuum to
clean bottom of pool.
Use Intex pool skimmer.
• Greenish water.
• Green or black
spots on pool liner.
• Pool liner is
slippery and/or has
a bad odor.
• Water turns blue,
brown, or black
when first treated
with chlorine.
• Water is cloudy or
milky.
• Level is lower than
on previous day.
• Dirt or sand on
pool floor.
• Leaves, insects
etc.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 17
English
SAFETY GUIDELINES
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
Demand constant supervision. A competent adult should be appointed as
a “lifeguard” or water watcher, especially when children are in and around
the pool.
Learn to swim.
Take the time to learn CPR and first aid.
Instruct anyone who is supervising pool users about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
Instruct all pool users, including children what to do in case of an
emergency.
Always use common sense and good judgement when enjoying any
water activity.
Supervise, supervise, supervise.
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 18
English
PARTS LIST
Your Krystal Clear™ Filter-Pump has been manufactured using the highest quality
materials and workmanship. All Intex products have been inspected and found free of
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal
Clear™ Filter-Pump and accessories listed below.
The following provision is only valid within the European member states countries: The
legal regulation of Directive 1999/44/EC will not be effected by this Intex warranty.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty is
invalid.
Krystal Clear™ Filter-Pump Warranty 2 Years
Hoses, Plunger Valves & Fittings Warranty 180 days
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet.
The Service Center will determine the validity of the claim.
IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN
NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR EMPLOYEES BE LIABLE
TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL
DAMAGES OR LIABILITIES.
This Limited Warranty does not apply if the products are subject to negligence, abnormal
use or operation, accident, improper operation, improper voltage or current contrary to
operating instructions, or to damage by circumstances beyond Intex’s control, including but
not limited to, ordinary wear and tear and damage caused by exposure to fire, flood,
freezing, rain, or other external environmental forces. This Limited Warranty applies only to
those parts and components sold by Intex. The Limited Warranty does not cover
unauthorized alterations, repairs or disassembly by anyone other than Intex Service
Center personnel.
The Limited Warranty is also not applicable if this product is used with another product
other than an Intex product, when setting up your pool.
The costs associated with the loss of pool water, chemicals or water damage are not
covered by this warranty. Injury or damage to any property or person is not covered by this
warranty.
LIMITED WARRANTY
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex Krystal Clear - 634T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex Krystal Clear - 634T in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex Krystal Clear - 634T

Intex Krystal Clear - 634T User Manual - German - 16 pages

Intex Krystal Clear - 634T User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info