686154
24
Zoom out
Zoom in
Previous page
1/27
Next page
(329PO) MODEL ECO5110&6110 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2017
329
PO
SAVE THESE INSTRUCTIONS
English
Page 24
TROUBLESHOOTING GUIDE
INSUFFICIENT
CHLORINE
WHITE FLAKES IN
THE WATER
NO LED DISPLAY
Insufficient operating hours of
the Saltwater System.
The salt level in the pool water
is less than 2000ppm. This is
insufficient.
Chlorine loss due to intense
sunlight exposure.
The bather load has increased.
Clogged or dirty electrolytic cell.
High UV level exposure.
Excessive calcium hardness is
present in pool water.
No power supply.
RCD/GFCI has not reseted.
A power fuse has blown.
LED failure.
Increase the daily Saltwater System
operating time. See “Operating Instructions”.
Check the salt level with the Test Kit. Adjust
as needed. See “Salt & Pool Water Volumes”.
Use a pool cover when the pool is not
in use and/or when the unit is operating.
Increase the daily Saltwater System
operating time. See “Operating Instructions”.
Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
Cover the pool with a pool cover for 2
days with the device running and then
test the water using the test strips.
If the pool is clean and clear, add stabilizer
to the water and then test the water with the
device running.
Drain about 20 to 25% of the pool
water and add fresh water to decrease
the calcium hardness. Inspect the
electrolytic cell for scale buildup. Clean
the electrolytic cell if necessary.
Find out the switch and turn on.
Reset the RCD/GFCI.
Contact Intex Service Center.
PROBLEM CAUSE SOLUTION
Operation is subject to the following two conditions:
(1)
this device may not cause interference,
and
(2)
this device must accept any interference, including interference that may cause
undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex ECO 5110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex ECO 5110 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info