685994

Intex Easy Set - 28122NP Manual

12
Zoom out
Zoom in
Previous page
1/19
Next page
86PO
S AVE THESE INSTRUCTIONS
(86PO) EASY SET POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/17/2016
English
Page 5
Barriers for Residential Swimming Pool Guidelines:
An outdoor swimming pool, including an inground, aboveground, or onground pool, hot tub, or spa, should be
provided with a barrier which complies with the following:
1.
The top of the barrier should be at least 48 inches above grade measured on the side of the barrier which
faces away from the swimming pool. The maximum vertical clearance between grade and the bottom of
the barrier should be 4 inches measured on the side of the barrier which faces away from the swimming
pool. Where the top of the pool structure is above grade, such as an aboveground pool, the barrier may
be at ground level, such as the pool structure, or mounted on top of the pool structure. Where the barrier is
mounted on top of the pool structure, the maximum vertical clearance between the top of the pool structure
and the bottom of the barrier should be 4 inches.
2.
Openings in the barrier should not allow passage of a 4-inch diameter sphere.
3.
Solid barriers, which do not have openings, such as a masonry or stone wall, should not contain
indentations or protrusions except for normal construction tolerances and tooled masonry joints.
4.
Where the barrier is composed of horizontal and vertical members and the distance between the tops of the
horizontal members is less than 45 inches, the horizontal members should be located on the swimming pool
sideofthefence.Spacingbetweenverticalmembersshouldnotexceed1-3/4inchesinwidth.Wherethere
aredecorativecutouts,spacingwithinthecutoutsshouldnotexceed1-3/4inchesinwidth.
5.
Where the barrier is composed of horizontal and vertical members and the distance between the tops of
the horizontal members is 45 inches or more, spacing between vertical members should not exceed 4
inches.Wheretherearedecorativecutouts,spacingwithinthecutoutsshouldnotexceed1-3/4inchesin
width.
6.
Maximummeshsizeforchainlinkfencesshouldnotexceed
1-1/4
inch square unless the fence is provided
withslatsfastenedatthetoporthebottomwhichreducetheopeningstonomorethan1-3/4inches.
7.
Where the barrier is composed of diagonal members, such as a lattice fence, the maximum opening formed
bythediagonalmembersshouldbenomorethan1-3/4inches.
8.
Access gates to the pool should comply with Section I, Paragraphs 1 through 7, and should be equipped
to accommodate a locking device. Pedestrian access gates should open outward, away from the pool, and
shouldbeself-closingandhaveaselflatchingdevice.Gatesotherthanpedestrianaccessgatesshould
have a self-latching device. Where the release mechanism of the self-latching device is located less than 54
inchesfromthebottomofthegate,(a)thereleasemechanismshouldbelocatedonthepoolsideofthe
gateatleast3inchesbelowthetopofthegateand(b)thegateandbarriershouldhavenoopeninggreater
than 1/2 inch within 18 inches of the release mechanism.
9.
Where a wall of a dwelling serves as part of the barrier, one of the following should apply:
(a)
All doors with direct access to the pool through that wall should be equipped with an alarm which
produces an audible warning when the door and its screen, if present, are opened. The alarm should
soundcontinuouslyforaminimumof30secondswithin7secondsafterthedoorisopened.Alarms
shouldmeettherequirementsofUL2017General-PurposeSignalingDevicesandSystems,
Section 77. The alarm should have a minimum sound pressure rating of 85 dBA at 10 feet and the
sound of the alarm should be distinctive from other household sounds, such as smoke alarms,
telephones, and door bells. The alarm should automatically reset under all conditions. The alarm should
be equipped with manual means, such as touchpads or switches, to temporarily deactivate the alarm for
a single opening of the door from either direction. Such deactivation should last for no more than 15
seconds. The deactivation touchpads or switches should be located at least 54 inches above the
threshold of the door.
(b)
ThepoolshouldbeequippedwithapowersafetycoverwhichcomplieswithASTMF1346-91listed
below.
(c)
Other means of protection, such as self-closing doors with self-latching devices, are acceptable so long
asthedegreeofprotectionaffordedisnotlessthantheprotectionaffordedby(a)or(b)described
above.
10.
Where an aboveground pool structure is used as a barrier or where the barrier is mounted on top of the
poolstructure,andthemeansofaccessisaladderorsteps,then(a)theladdertothepoolorsteps
shouldbecapableofbeingsecured,lockedorremovedtopreventaccess,or(b)theladderorsteps
should be surrounded by a barrier. When the ladder or steps are secured, locked, or removed, any
opening created should not allow the passage of a 4-inch diameter sphere.
Barriers should be located so as to prohibit permanent structures, equipment or similar objects from being
used to climb the barriers.
86PO
S AVE THESE INSTRUCTIONS
(86PO) EASY SET POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/17/2016
English
Page 6
NOTE:
Drawings for illustration purpose only.
Actual product may vary.
Not to scale.
For Pools with Dual Suction Outlets Conguration:
InordertocomplywiththerequirementoftheVirginiaGrahameBakerAct(forUSAandCanada),your
poolisdesignedwithdualsuctionoutletsandoneinletttings.Overviewofthedualsuctionoutlets
congurationisasfollow:
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
17’ (518 cm) & above Easy Set
®
pools
16’ (488 cm) & below Easy Set
®
pools
4
5
10 9
8
2
11
6
7
1
3*
20
21
22
12
13 14
15
16
17
18
19 9
8
6
7
1
3
4
5
21
86PO
S AVE THESE INSTRUCTIONS
(86PO) EASY SET POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/17/2016
English
Page 7
REF
NO.
DESCRIPTION
POOL SIZE & QUANTITIES
6’
(183 cm)
8’
(244 cm)
10’
(305cm)
12’
(366cm)
13’
(396cm)
15’
(457cm)
16’
(488cm)
18’
(549cm)
1
POOLLINER(DRAINVALVECAPINCLUDED)
1 1 1 1 1 1 1 1
2 STRAINERHOLEPLUG 3 3 3 3 3 3 3 2
3 GROUNDCLOTH(OPTIONAL) 1 1 1
4 DRAIN CONNECTOR 1 1 1 1 1 1 1 1
5 DRAIN VALVE CAP 1 1 1 1 1 1 1 2
6 STRAINER CONNECTOR 2 2 2 2 2 2 2 2
7 STRAINERGRID 2 2 2 2 2 2 2 2
8 HOSE 2 2 2 2 2 2 2 2
9 HOSECLAMP 8 8 8 8 8 8 8 4
10 HOSET-JOINT 1 1 1 1 1 1 1
11 POOLINLETJETNOZZLE 1 1 1 1 1 1 1
12 HOSEO-RING 1
13
PLUNGERVALVE(HOSEO-RING&STEPWASHERINCLUDED)
1
14 STEPWASHER 1
15 STRAINER NUT 1
16 FLATSTRAINERRUBBERWASHER 1
17
INLETTHREADEDAIRCONNECTOR+
1
18
ADJUSTABLEPOOLINLETJETNOZZLE
1
19 SPLITHOSEPLUNGERVALVE 1
20
INLET STRAINER CONNECTOR
1 1 1 1 1 1 1
21
AIRJETVALVE
1 1 1 1 1 1 1 1
22
POOLINLETAIRADAPTOR+
1 1 1 1 1 1 1
23
AIRJETVALVECAP(NOTSHOWN)
1 1 1 1 1 1 1 1
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
+Ifapplicable,dependingonthesizeofthelterpumpttedwithyourpool,youmustquotethemodel
numbershownonthelterpumphousingtoorderthecorrectsizeof“
Pool Inlet Air Adaptor
”or
“Inlet
Threaded Air Connector”
replacement part.
86PO
S AVE THESE INSTRUCTIONS
(86PO) EASY SET POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/17/2016
English
Page 8
REF
NO.
DESCRIPTION
6’ X 20”
(183cm X 51cm)
8’ X 30”
(244cm X 76cm)
8’ X 30”
(244cm X 76cm)
Clearview
10’ X 30”
(305cm X 76cm)
10’ X 30”
(305cm X 76cm)
Printing
12’ X 30”
(366cm X 76cm)
12’ X 30”
(366cm X 76cm)
Printing
12’ X 36”
(366cm X 91cm)
SPARE PART NO.
1
POOLLINER(DRAINVALVECAPINCLUDED)
11588EH 12128EH 11246EH 12129EH 11303EH 10200EH 11304EH 10319EH
2 STRAINERHOLEPLUG 10127 10127 10127 10127 10127 10127 10127 10127
3
GROUNDCLOTH(OPTIONAL)
4 DRAIN CONNECTOR 10184 10184 10184 10184 10184 10184 10184 10184
5 DRAIN VALVE CAP 10649 10649 10649 10649 10649 10649 10649 10649
6 STRAINER CONNECTOR 11070 11070 11070 11070 11070 11070 11070 11070
7 STRAINERGRID 11072 11072 11072 11072 11072 11072 11072 11072
8 HOSE 11873 11873 11873 11873 11873 11873 11873 11873
9 HOSECLAMP 11489 11489 11489 11489 11489 11489 11489 11489
10 HOSET-JOINT 11871 11871 11871 11871 11871 11871 11871 11871
11 POOLINLETJETNOZZLE 12364 12364 12364 12364 12364 12364 12364 12364
12 HOSEO-RING
13
PLUNGERVALVE(HOSEO-RING&STEPWASHERINCLUDED)
14 STEPWASHER
15 STRAINER NUT
16
FLATSTRAINERRUBBERWASHER
17
INLETTHREADEDAIRCONNECTOR+
18
ADJUSTABLEPOOLINLETJETNOZZLE
19
SPLITHOSEPLUNGERVALVE
20
INLET STRAINER CONNECTOR
12365 12365 12365 12365 12365 12365 12365 12365
21
AIRJETVALVE
12363 12363 12363 12363 12363 12363 12363 12363
22
POOLINLETAIRADAPTOR+
12366
12367
12368
12366
12367
12368
12366
12367
12368
12366
12367
12368
12366
12367
12368
12366
12367
12368
12366
12367
12368
12366
12367
12368
23
AIRJETVALVECAP(NOTSHOWN)
12373 12373 12373 12373 12373 12373 12373 12373
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
+Ifapplicable,dependingonthesizeofthelterpumpttedwithyourpool,youmustquotethemodel
numbershownonthelterpumphousingtoorderthecorrectsizeof“
Pool Inlet Air Adaptor
”or
“Inlet
Threaded Air Connector”
replacement part.
86PO
S AVE THESE INSTRUCTIONS
(86PO) EASY SET POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/17/2016
English
Page 12
POOL SETUP (continued)
2
3
IMPORTANT
Properinationofthetopring.
The ambient temperatures of air and water have an effect on the internal pressure of the top ring. To
maintain a correct internal pressure, it is best to leave some room for expansion as the sun heats the
air inside the ring. During very hot weather, you must check to see whether it is necessary to release
some air. This is to avoid any possible damage to the ring.
In no event shall Intex, their authorized agents or employees be liable for damages (such as pin
holes) to the inatable top ring caused by negligence, ordinary wear and tear, abuse and
carelessness, or external forces.
YoumayhavepurchasedthispoolwiththeIntexKrystalClear™lterpump.Thepumphasits
ownseparatesetofinstallationinstructions.Firstassembleyourpoolunitandthensetupthelter
pump.
Estimatedassemblytime10~30minutes.(Notetheassemblytimeisonlyapproximateand
individualassemblyexperiencemayvary.)
1. Liner preparation
•
Findaat,levellocationthatisfreeandclearofstones,branchesorothersharpobjectsthatmay
puncture the pool liner or cause injury.
• Openthecartoncontainingtheliner,etc.,verycarefullyasthiscartoncanbeusedtostorethepoolduring
the winter months or when not in use.
• Takeoutthegroundcloth
(3)
and spread it over the cleared area.
Then take out the liner
(1)
and spread it out over the ground cloth,
with the drain valve directed towards the draining area. Place the
drain valve away from the house.
IMPORTANT: Always set up the pool unit with at least 2
persons. Do not drag the liner across the ground as this can
cause liner damage and pool leakage (see drawing 2).
• Duringthesetupofthepoolliner,pointthehoseconnectionsor
openings in the direction of the electrical power source. The
 outeredgeofthepoolshouldbewithinreachofthepump’s
electrical connection.
• Layoutthepool.Spreadouttheplainbluesidesandmakethe
 pooloorassmoothaspossible
(see drawing 2).
2. Ring ination
• Flipthetopringoutandcheckthatitisfullyoutsideofthewall
 liningandfacingup.Inatetheringwithamanualairpump
(see
drawing 3)
.Keepthetopringcenteredinthemiddleofthepool,
while doing this.
IMPORTANT: Prevent bursting by not using a high-pressure
pump, such as an air compressor. Do not over inate.
Preferably use an Intex manual ination hand pump
(not included).
3. Hose connectors
• Thefollowingappliestopoolliners
with
hoseconnectors(16"(488cm)&belowpools).Ifthepoolwas
purchased
without
alterpump,inserttwoblackplugs
(2)
intotheblacklterpumpoutlets.Dothis
 fromtheinsideofthepoolsothatwaterwillnotrunoutwhenllingit.
• Ifthepoolwaspurchased
with
alterpump,readtheKrystalClear™FilterPumpManualrstand
then
proceed to next installation step.
1
WATER
LEVEL
Level
FILL LINE
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex Easy Set - 28122NP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex Easy Set - 28122NP in the language / languages: English as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex Easy Set - 28122NP

Intex Easy Set - 28122NP User Manual - German - 12 pages

Intex Easy Set - 28122NP User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info