Manual Intex CS20110 Krystal Clear (page 21 of 38) (English)

752348

Zoom out

Zoom in

1/38

(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012

159

SAVE THESE INSTRUCTIONS

Page 21

English

SALTWATER SYSTEM OPERATION (continued)

OPERATING INSTRUCTIONS

6. Boost cycle

• Ifthetestresultisbelow0.1ppm,pressandhold“BOOST”

button for 5 seconds until the indicator lights up and the

LED display display “80”. This indicates that the saltwater

system has started copper ion and more chlorine sanitizer

 production.Youcanpressandholdthe“BOOST”buttonfor

another 5 seconds until the indicator is off, which will cancel

 theBoostcycle.

Note: Once the system has started copper ion and more

chlorine sanitizer production, the boost button can’t be re-set until the power

switch is off.

• The boost operating hours is 8 times the amount of time programmed into the

system, i.e. if your saltwater system operating time is 2 hours, the boost procedure

will run 8 x 2 = 16 hours. After boost procedure has been completed, the system

will automatically switch to the normal working mode.

• Afteraheavyrainorifthepoolisdirty,pressthe“BOOST”buttontoshockthe

pool again.

7. Test pool water regularly:

Once the copper level appears to be balanced, test the pool water every week

to maintain the proper sanitizer level.

It’s very important that the free chlorine is between 0.5-3 ppm and copper

ion concentration is between 0.1~0.2 ppm. When the copper level is below 0.1

ppm, repeat step 6.

NOTE:AHighcopperionconcentrationmaycauseblondehairtoexhibita 

green hair. To prevent this, wear a swimming cap during swimming, and wash

hair with special shampoo after using the pool.

 See“TroubleshootingGuide”.

8. Stand-by/power saving mode:

• When the cycle ends, the green “SLEEP” indicator on the

control panel lights up and the LED display flashes “93”.

 ThesystemisnowinStand-Bymode.Afterawhile,it 

shuts down and sets itself in a Power Saving mode. The

system will automatically turn itself back on in 24 hours,

starting its daily cycle of chlorine production.

• The “SLEEP” indicator stays on, while the system is in the

Power Saving mode. The LED display however, goes blank

after 1 hour. Press any button ( or ) to view the last LED

code.

9. Running the pump alone without the Saltwater System:

To run the pump alone without the Saltwater System function,

press and hold both ( ) and ( ) buttons for 5 seconds

 untilyouheara“beep”andtheLEDdisplayshows“FP”.

The pump is now operating alone. To stop the pump,

 manuallyturntheswitchOFF.NOTE: The pump cannot

be operated alone under an automatic timer mode.

IMPORTANT: To keep the initial automatic operating cycle

 settingoftheSaltwaterSystem,turntheswitchON,the

 LEDdisplayshows“FP”,thenunlockandlockthekeypad

controls again, see previous steps 2 and 3. The LED display shows

the initial input hours and the Saltwater System cycle repeats again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Intex CS20110 Krystal Clear in the language / languages: English as an attachment in your email.

The manual is 12,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Intex CS20110 Krystal Clear Manual

Product: