752338
13
Zoom out
Zoom in
Previous page
1/14
Next page
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 03/28/2012
98A
SAVE THESE INSTRUCTIONS
Page 13
Disassembly and Storage
First clean your boat thoroughly following the Care and Maintenance instructions. Open all air valves
and deflate boat completely. Remove all the accessories from the boat; seats, fishing rod holders,
oars, gear pouch and battery pouch.
Fold the left and right chambers of the boat towards the middle of the floor. It is not necessary to
remove the slats to fold the boat. Fold the bow end twice to the middle of the boat tightly while
forcing out any remaining air; repeat this procedure for the stern. With two opposing folded sides,
fold one end over the other like closing a book. Replace all inflation valve caps. Your boat is ready
for storage. Fold the boat loosely and avoid sharp bends, corners and creases which can damage
the boat.
Troubleshooting
If your boat appears a bit soft, it might not be because of a leak. If the boat was inflated late in the day
with 32 °C (90 °F) air, that air might cool down to 25 °C (77 °F) overnight. The cooler air exerts less
pressure on the hull, so it could appear soft the next morning.
If there has been no temperature variation, you need to start looking for a leak:
• Take a good look at your boat from just a few feet away. Flip it over and closely check over the
outside. Any large leaks should be clearly visible.
• If you have an idea where your leak is, use a mix of dishwashing liquid and water in a spray
bottle, and spray over the suspicious areas. Any leak will produce bubbles that will pinpoint the
location of the leak.
• Check valves for leak, if necessary, spray soapy water around the valve and the valve base.
Repairs
Through constant use you may occasionally puncture your boat. Most leaks only take a few minutes to
repair. Your boat comes with a repair patch, and additional repair supplies can be ordered from Intex
Consumer Service or from our website.
First locate the leak; soapy water will bubble out from the source of the leak. Thoroughly clean the
area surrounding the leak to remove any dirt or grime.
Cut a piece of repair patch large enough to overlap the damaged area by approximately 1.5 cm (1/2”).
Round off the edges, and place the patch on the damaged area and PRESS DOWN FIRMLY. You
may want to use a weight on top to keep it in place.
Do not inflate in 30 minutes after patching.
If the patch does not hold, you can purchase a PVC or silicon based glue for repairing camping mats,
tents or shoes from your local market to patch your boat, please refer to the instruction of the glue for
patching.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex Challenger Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex Challenger Series in the language / languages: English as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex Challenger Series

Intex Challenger Series User Manual - German - 14 pages

Intex Challenger Series User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info