587278

Intex 604G Krystal Clear filterpomp Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
58GS
SAVE THESE INSTRUCTIONS
(58GS) MODEL 604G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/04/2016
English
Page 5
SETUP INSTRUCTIONS
Be sure you have access to water to fill the pool and chemicals for the water.
IMPORTANT: This filter pump is shipped with the air release valve (1) open (open the air
release valve if necessary). DO NOT replace the air release valve until you reach STEP #8.
Failure to follow these instructions will result in air trapped inside filter housing; the motor
will run dry, be noisy and malfunction.
1.
Assemble above-ground-pool first. Carefully follow the pool’s installation instructions.
2.
Place the filter pump the length of the hose away from the pool wall where the lower black
protruding hose connection is "sticking-out". Ensure the filter pump is accessible at all time for
service and maintenance.
3.
Insert the nozzle union
(14 & 10)
into the upper protruding hose connections, and then attach
the pool inlet air adaptor
(16)
to the upper protruding fitting. Screw the air jet valve
(15)
over
the pool inlet air adaptor
(16)
. Then insert the strainer union
(9 & 11)
into the lower protruding
hose connections. The hoses
(8)
fit over the strainers inserted into the connections.
4.
There are two hoses to be connected to the filter pump hose connections. With hose clamps
(7)
,
fasten one of the hoses
(8)
to the lower protruding hose connection (marked "+" on the pool
liner) and to the upper pump connection (marked "+").
5.
Connect the second hose to the pool inlet air adaptor
(16)
and to the lower pump connection.
Make sure all the hose clamps
(7)
are tight.
NOTE:
Make sure the air jet valve
(15)
is securely
tighten onto the pool inlet air adaptor
(16)
and facing up.
6.
In a counter-clockwise motion unscrew the threaded filter housing collar
(13)
from the filter
housing. Grasp and remove the housing cover
(3)
. Check to see if a cartridge is inside the
housing. If yes, replace the cover, finger tighten the housing collar
(13)
back onto the filter
housing.
7.
Fill the pool to a level of at least 1-2 inches above the top connection. The water will
automatically flow down into the pump.
8.
When water starts flowing out of the air release valve hole, screw in the air release valve back
into the filter housing cover. Do not over tighten the valve.
NOTE: Venting the system is
necessary for air to escape as the filter housing fills with water.
9.
Connect the filter pump power cord end to the transformer output receptacle and screw in the
cover. Plug the transformer power cord into a properly installed electrical socket.
10.
Operate the filter pump until the desired water clarity is obtained.
NOTE:
Never put pool chemicals directly into the filter pump. This may damage the pump
and void the warranty.
WARNING
Risk of electric shock. Connect transformer only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or residual
current device (RCD). Contact a qualified electrician if you cannot verify
that the receptacle is protected by a GFCI/RCD. Use a qualified electrician
to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a
portable residual current device (PRCD).
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex 604G Krystal Clear filterpomp at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex 604G Krystal Clear filterpomp in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex 604G Krystal Clear filterpomp

Intex 604G Krystal Clear filterpomp User Manual - German - 14 pages

Intex 604G Krystal Clear filterpomp User Manual - Dutch - 15 pages

Intex 604G Krystal Clear filterpomp User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info