752320
9
Zoom out
Zoom in
Previous page
1/13
Next page
87A
SAVE THESE INSTRUCTIONS
English
(87IO) METAL FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 06/04/2019
Page 9
The last joint connection may be difficult to complete. You can
do it though, if you first simultaneously raise the last joint and
beam about 2 inches (5 cm). Now insert the beam into the joint
while lowering the pieces into position. The beam will easily
slide into the joint (see drawing 2.3). Ensure that the last joint
is fully connected before proceeding to connecting the legs.
3. Vertical legs assembly
Attach the leg’s end cap (4) to the bottom of each leg (7) first.
With the beams and T-joints assembly resting on the ground, slide
one vertical leg into the belt loop located in the middle of the pool
liner and insert the top of the leg into the bottom of the T-joint (3)
(see drawing 3.1). Continue the process with all the vertical legs.
Lift the beams assembly and make sure all the legs are in a vertical
position
(see drawing 3.2). Push all the T-joints downward to
ensure they are firmly connected to the legs.
Pull gently, in an outward direction, the bottom of the leg making
sure the leg is vertical and perpendicular to the level ground.
4. Filling of the pool
The following applies to pool liners with hose connectors (16’ (488 cm) & below pools). If the pool was
purchased without a filter pump, insert two of the three plugs (10) into the black filter pump outlets. Do
this from the inside of the pool so that water will not run out when filling it. If the pool was purchased
with a filter pump, read the Krystal Clear™ Filter Pump Manual first and then proceed to next installation
step.
Before filling the pool with water, ensure that the drain plug inside the pool is closed and that the drain
cap on the outside is screwed on tightly. Fill the pool with no more than 1 inch (2.5 cm) of water. Check
to see whether the water is level.
IMPORTANT: If the water in the pool flows to one side, the pool is not completely level. Setting
up the pool on unlevel ground will cause the pool to tilt resulting in the sidewall material bulging
and a potential collapse of the pool. If the pool is not completely level, you must drain the pool,
level the area or move the pool to a different area that is level, and re-fill the pool, following the
above directions.
Smooth out the bottom liner wrinkles (from inside the pool) by pushing out where the pool floor and pool
sides meet. Or, (from outside pool) reach under the side of the pool, grasp the pool floor and pull in an
outward direction. If the ground cloth is causing the wrinkles, have 2 people pull from opposite sides to
remove all wrinkles. Use the properly assembled pool ladder when entering or exiting the pool during this
process. Also make sure all the legs are vertical and perpendicular to the ground.
Fill the pool with water up to just below the sleeve line.
(see drawing 4).
POOL SETUP (continued)
4
WATER LEVEL
3.2
7
4
3.1
7
4
3
2.3
3
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex 28208 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex 28208 in the language / languages: English as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex 28208

Intex 28208 User Manual - German - 13 pages

Intex 28208 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info