Manual Interphone-Cellularline Fbeat (page 7 of 9) (English)

616639

Zoom out

Zoom in

1/9

1.0 PREPARATION/ASSEMBLY

InterphoneFBEAT is a modular audio kit made up of a Blue-

tooth® module (the core of the system) (A), a double slide

support system for the module (E/D) and an audio kit with

a double microphone to be installed inside the helmet (C/B)

Before conﬁguring the InterphoneFBEAT, you should check

the website for software updates that could improve the

performance of the FBEAT. If there are any updates, instal-

lation is recommended.

Verify compatibility with the operating system on your PC,

then download the ﬁle and the attached instructions that

will guide you through the update process.

1.1 Mounting the bracket on the helmet

The InterphoneFBEAT has two mounting systems (small

plates) (E/D) that you can install on the helmet. Choose the

system that is better suited to the type of helmet you are

using.

Equipped with a sliding latch system, the plates support

and lock the FBEAT Bluetooth® module into position. One

system is applied using an adhesive system (E), and the

other uses a clip (D).

Thanks to the sliding latch system on the plates, the FBEAT

module can easily be removed for recharging, updating,

security against theft, and use on other helmets that have

already been prepared with other kits designed for each

type of helmet.

The kits for an additional helmet all consist of an audio sec-

tion with earphones/microphone, along with two support

plates for the module.

The kits for an additional helmet are optional and can

have a diﬀerent structure and operation. For more in-

formation, consult the accessory section on our website,

www.interphone.com

We recommend using the adhesive plate (E) since it is

more aerodynamic and can be placed wherever you like on

the surface of the helmet. This allows you to choose point

that best suits the shape of the helmet shell to maximize ap-

pearance and adhesion.

On the other hand, the adhesive plate cannot be reposi-

tioned. Once it is applied, it cannot be removed because the

3M adhesive that provides its excellent holding power does

not allow for a change of position. If the plate is removed, it

must be replaced with a new one.

Carefully choose the most suitable point before application.

The clip-on plate (D) is better for those who do not want

to apply permanent adhesive to their helmet or would like

to be able to remove the plate and use the helmet with no

accessories installed.

The clip-on plate requires that the helmet allow part of the

plate to be inserted between helmet shell and cheekpad.

The cheekpads on some helmets are glued or have special

seals that prevent the plate from being inserted correctly or

require the helmet to be modiﬁed, which not everyone is

willing to do. In these cases, it’s better to choose the adhe-

sive plate.

Both brackets can only be installed on the left side of the

helmet.

Installation with (adhesive) plate

Take the adhesive plate, but do not remove the protective

ﬁlm on the back. Place the plate on the left side of the hel-

met shell. Now, move it around and ﬁnd the position where

it will adhere and function best. Before applying it, mount

the FBEAT module on the plate and check whether the posi-

tion you chose could disturb the driver by causing interfer-

ence or discomfort (check visor, opening, etc...).

Carefully clean and degrease the point chosen for apply-

ing the plate. Do not use strong detergents that could ruin

the paint on the helmet. After cleaning the helmet shell,

remove the protective ﬁlm from the double-sided adhesive

strip and apply the plate on the helmet. Press quickly on the

plate to attach the strip ﬁrmly.

After application, it is a good idea to let the 3M adhesive act

on the helmet for 12 hours before using the helmet.

Installation with the clip-on (removable) plate

Check the type of helmet you have and make sure that the

clip can be inserted between helmet shell and cheekpad.

Otherwise, use the adhesive plate.

Take the clip-on plate, loosen the two screws and remove

the rear section.

On the left side of the helmet, locate the most suitable point

for inserting the clip, slide the rear section of the clip in be-

tween the helmet shell and the cheekpad, and let the end

(with the holes for the screws) protrude on the outside. Now,

try to join the front section of the clip onto the rear section.

Depending on the thickness/radius of the helmet, it may be

necessary to use the adapter (J) to compensate for the dis-

tance between the two sections so that the clip still adheres

to the helmet shell when the screws are tightened.

Tighten the screws with the screwdriver provided. Do not

use excessive force when tightening the screws. You could

break all or part of the clip.

If you are also using the adapter for the clip, you must re-

place the two screws installed in the clip with the longer

ones supplied with the unit.

1.2 Installing the audio section

Wear the helmet and locate the exact point where your

ears are positioned inside.

If the internal fabric of the helmet allows it, try to apply

the two earphones in the audio kit directly at the points

you determined. The Velcro on the back of the earphone

will often adhere perfectly to the material in the helmet

without the need to use the fabric strip (I) with double-

adhesive. Otherwise, if the material is unmanageable,

apply the strip of fabric at the point you previously deter-

mined and place the earphone on the strip.

Put on the helmet once again and check whether the ear-

phones are correctly positioned. They must be centred

and come slightly in contact with your ears.

If the helmet allows it, it’s a good idea to insert the ear-

phones under the cheekpad fabric, which requires more

time and care to accomplish but makes the internal kit

almost invisible and more comfortable.

Thread the cable with plug under the cheekpad and

around the helmet while trying not to lay it over itself or

twist it. Then, pull it out on the left side as far as it will

go. Afterwards, when the plug is connected to the FBEAT

module mounted on the support, you can push the ex-

cess cable back inside and leave only as much as you

need on the outside.

Microphone (B) - if possible, slide the microphone arm

through the hole in the chin strap and below the cheek-

pad so that the microphone is more stable and less ob-

trusive. It should be possible to position the microphone

with foam windscreen (14) in front of your mouth, but it

may be left slightly to the side of the mouth.

After installation is complete, make sure that the wording

MIC on the foam windscreen on the microphone arm fac-

es your mouth and preferably points toward your eyes.

1.3 Recharging

The InterphoneFBEAT must be charged before use.

Once mounted on the helmet, connect the recharger ca-

ble provided (F) to a USB port, then insert the recharger

cable plug into the outlet on the audio kit connector (16)

correctly inserted in the InterphoneFBEAT module.

The charge LED turns orange (7) during charging.

When the battery is fully charged, the LED will turn green.

About two hours are needed to charge the FBEAT mod-

ule completely. Two modules can be charged together in

around three hours.

We recommend turning the module oﬀ before recharg-

ing the FBEAT.

1.4 Turning on/oﬀ

TURNING ON

Press and hold the MFB button for approximately 3 seconds.

The speaker will sound an acoustic warning and the LEDs will

begin ﬂashing quickly for around 3 seconds.

Subsequently, in stand-by mode, the LED will ﬂash approxi-

mately once every 5 seconds.

TURNING OFF

Press and hold the MFB button. The speaker will sound a pro-

longed acoustic warning and the LED will ﬂash red prior to

turning oﬀ.

2 PAIRING

2.1 Telephone

Pairing

The INTERPHONE FBEAT can be paired to a mobile phone.

After having turned the INTERPHONE FBEAT oﬀ, press and

hold the MFB button until the warning light alternates red

and blue ashes. This will take about 8 seconds.

When the light is ﬂashing red/blue alternately perform the

device search from your telephone (refer to the telephone or

navigator manual).

The telephone or navigator will detect the INTERPHONE

FBEAT. Simply select it, and enter the numerical code 0000.

To use with a mobile telephone and GPS navigator at the

same time, see point 2.3.

2.2 Intercom

Pairing

After having turned the INTERPHONE FBEAT oﬀ, press and

hold the MFB button until the warning light alternates red

and blue ashes. This will take about 8 seconds.

When both LEDs ﬂash red/blue alternately, press and release

the MFB button on one of the two INTERPHONE FBEATs.

The two INTERPHONE FBEATs are connected when both

LEDs show a ﬁxed blue light.

2.3 Audio GPS

Pairing

For an audio connection, GPS NAVIGATORS use the TELE-

PHONE (headset) proﬁle: to pair the phone during use of the

navigator you must use the speciﬁc function on the GPS de-

vice. For further information and settings, please consult the

navigator manual.

3 USE

3.1 Telephone function

To answer a call: when a call comes in, the speaker sounds a

warning tone or the telephone ring: to answer, brieﬂy press

the MFB button.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Interphone-Cellularline Fbeat in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Interphone-Cellularline Fbeat

Interphone-Cellularline Fbeat User Manual - German - 9 pages

Interphone-Cellularline Fbeat User Manual - French - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Interphone-Cellularline Fbeat Manual

Product: