738445
21
Zoom out
Zoom in
Previous page
1/36
Next page
M10 x 55 Hex Bolt (Blue Dot)
1/2” Step Spacer
Lower Cable inside tube
M10 x 50 Hex Bolt
M10 x 35 Hex Bolt
Cable Anchor Plate
Step 18
1 - Lower Cable
1 - M10 x 35 Hex Bolt
1 - M10 x 50 Hex Bolt
1 - M10 x 55 Hex Bolt (Blue Dot)
4 - M10 Flat Washers
2 - M10 Locknut
1 - 1/2” Step Spacer
1 - Plastic Ball
1 - “U” Bracket
1 - Spring Clip
1 - M6 x 20 Button Head Bolt
1 - M6 Flat Head Nut
Step 18: Select a Lower Cable (with “U” Bracket). Lay it out assuring it is not kinked. Attach the “U”
Bracket to the Cable Anchor Plate upper center hole. Route the cable up through the Floating Pulley
Assembly with Guide Bushing, then down around the rear pulley position and into the Base Beam. Push
the cable forward through the Base Beam past the front pulley position. Route the cable out through
the smaller hole and up around the Lower Cable Column Mount Pulley, capturing the cable between the
pulley and the lower cable retainer tab only. Install the front and rear Pulleys assuring that the cable is
seated in their grooves. Route the cable up the Cable Column and between the Dual Pulleys on the
Cable Column Slider. To secure the Cable End, place one Plastic Ball onto the end of the cable. Next
slide the cable end into the slot of the Cable End “U” Bracket. Finally, attach the Spring Clip to the “U”
Bracket using the M6 x 20 Button Head Bolt and M6 Flat Head Nut. Slide the retainer “O” Ring tight
against the Plastic Ball to complete using:
One (M10 x 35 Hex Bolt) One (Plastic Ball)
One (M10 x 50 Hex Bolt) One (“U” Bracket)
One (M10 x 55 Bolt (Blue Dot) One (Spring Clip)
Four (M10 Flat Washers) One (M6 x 20 Button Head Bolt)
Two (M10 Locknuts) One (M6 Flat Head Nut)
One (1/2” Step Spacer)
(Wrench Tighten Now)
Page 18
Lower Cable “U” Bracket
and Anchor Plate
Floating Pulley Assy.
with Guide Bushing
Front Pulley
Cable Column Mount Pulley
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inspire SCS-202 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inspire SCS-202 in the language / languages: English as an attachment in your email.

The manual is 4,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info