738436

Inspire CR2.5 Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
Page | 20
selected, the program will launch. If “Timer ON” was entered, “Set TIME” and “30:00” will begin to flash.
Adjust the time value, pressing ENTER to confirm and launch the program.
Program Launch A consistent heart rate signal is required for the Heart Rate programs to operate. If no signal is detected,
the NO HR SIGNAL banner will flash. If 30 seconds elapse without a heart rate signal, the program will
automatically end, and the Wake Mode will launch.
When the HR programs launch, the selected heart rate target (example: “HR target = 123 bpm”) will flash
in the 13x94 Brickyard Display. If a timer was selected, the timer will begin to count down from the entered
time value. If the timer was not added, the timer will count upward continuously until the program is
manually ended.
If the user’s pulse value ever varies more than 10%+/- from the selected target, the console will begin to
post instructional messages such as “HR too LOW” and “Speed UP!” If the user’s heart rate ever equals or
exceeds 100% of the calculated Maximum Heart Rate (MHR), warnings will post in the 13x94 Brickyard
Display and the speaker will sound every 10 seconds. As a safety measure, when operation at or above the
user’s calculated MHR, the program will automatically end.
End Program Heart Rate Programs will run continuously until either the user presses the STOP key or the value set for the
optional timer has elapsed.
MAINTENANCE
General
All Inspire models are engineered for years of operation. Let
noise be your first indication that a repair or adjustment is
required. Please discontinue use immediately and contact an
Authorized Service Technician or Fitness Dealer if an unusual
noise, scraping, knocking, grinding or vibration is detected.
Often, a minor issue will become a major repair if ignored
and use is continued.
Prior to each workout, confirm that all adjustment levers and
screws are tightened.
The CrossRower is manufactured of the most durable
materials available. The plastics are molded of strong and chemical-resistant ABS and PVC. The frame is produced of high-tensile steel and
protected with an industrial-grade, powder paint coating for the highest level of corrosion resistance. It is important to note however, that
perspiration can be extremely corrosive if allowed to accumulate on the machine. After training, always wipe down the unit with a mild soap
solution followed by a thorough drying with a clean towel. Positioning a small spray bottle and towel near the unit will help ensure that your
equipment looks new for many years.
NOTE: Perspiration is very corrosive and if allowed to remain on the machine, will cause discoloration, fading,
rust and odors. Unfortunately, these conditions are not covered under the Warranty Policy.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inspire CR2.5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inspire CR2.5 in the language / languages: English as an attachment in your email.

The manual is 6,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info