509747

Innovate LC-1 Manual

6
Zoom out
Zoom in
Previous page
1/24
Next page
- 6 -
2.2 Connecting the LC-1 to an ECU or data logger
All Innovate MTS devices like the LC-1 with dual serial ports should have their system grounds
connected together to a common ground point. If an external data logger or ECU is to be fed by
an MTS device, the MTS ground should be located at or near the ECU or data logger’s input
signal ground. Some ECU’s or data loggers have differential inputs. A differential input has a
separate ground INPUT for each sensor input. This ground input MUST be connected also to
ground as shown in these diagrams. If one analog output of the LC-1 is used to drive an AFR
display and the other output is used to connect to an ECU, the AFR display ground should be
connected to the ECU ground. The schematics below can also adapted for 7-wire LC-1s.
Simply wire the Green analog ground wire with the System ground.
2.3 Electrical Grounding Concerns
The electrical environment inside a car provides unique challenges, combining high voltages and
currents, low-voltage signals, convoluted signal paths, and variable conditions (i.e., fans turning
on and off, or starter cranking).
When using precision electronics, it is important for ALL electronics to share a common ground.
Remember that “Ground” is more than just the return path for any circuit- it is also the reference
against which any voltage is measured.
Since it is not always practical to ground every device to the exact same location, here are some
tips on grounding:
1. The BEST grounding scheme is all grounds (i.e., ECU, Gauges, LC1 heater, LC1
system, etc.) SOLDERED into a single lug and bolted to the engine block.
2. The next best is all grounds attached to the same source, as close as possible, but on
separate lugs. This is because even the corrosion between lugs can create ground
offset and noise. Incidentally, this is why many ECUs have separate ground wires for
injectors vs. ECU system ground- separating high voltages and low voltages reduces
noise.
3. Grounding to the engine block is usually better than grounding to the frame.
4. Grounding a gauge to the radio is usually bad- ground offset can vary with volume.
5. Grounding to an ECU housing is generally not optimal- housings are strapped to the
frame for shielding, but not necessarily grounded.
6. One of the WORST things to do is to ground most of your electronics to one place (i.e.
the engine block), but ground one device somewhere else (i.e., the frame). Not only can
this result in ground offsets, it can also create a “path of least resistance” for high
currents THROUGH a low-current device. This can result in melted wires and vaporized
diodes, when, for example, starter currents flow through gauges.
2.4 Mounting the sensor using a Bung.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Innovate LC-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Innovate LC-1 in the language / languages: English as an attachment in your email.

The manual is 0,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info