800947
14
Zoom out
Zoom in
Previous page
1/16
Next page
14
of water and vinegar to clean the inside and outside of the ice maker. Do not spray chemicals
or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.
Keep the ventilation openings of the unit clear of obstructions. Do not use mechanical devices
or other means to speed up the defrosting process.
Periodically reuse the machine after a period of inactivity; there may be a need to add water
to the tank.
To ensure proper ice hygiene, change the water in the water tank at least once a day. If not
used for a long time, drain the water and replace it.
Always use potable water for ice production both on first use and after a long period of
inactivity.
TROUBLE SHOOTING
1. In the event of a power failure due to disconnection of the power cord or if the power
button was pressed during an ice-making cycle, it is possible that small pieces of ice may form
and become stuck in the blade. automatic causing jamming. In this case, the ice fragments can
be removed by unplugging the power cord and gently pushing the shovel back, so that you
have access to the fragments and can remove them, and then start the machine.
PROBLEM POSSIBLE CAUSE SOLUTION
Compressor malfunctions
with noise The voltage is lower than
recommended Turn off the machine and
do not restart it until the
voltage is adequate.
Add water light on 1. There is no water
2. The pump is filled with
air
1.Add a little water
until reaching the MAX
position
2.Press the POWER button
to restart
The indicators on the
display do not light up Blown fuse / No power Replace the fuse / Turn on
the machine
The ice produced is too
big and the cubes stick
together
Ice from previous cycles
left in the water tank Take out the ice in stand-
by mode
The ice making process is
running, but no ice has
come out
1. The compressor has no
refrigerant
2. Compressor damaged
3. Fan motor damaged
Call customer service
All indicators flash at the
same time 1. The water tray is blo-
cked by the ice cube
2. The motor is stuck,
moving or damaged
3. Micro switch damaged
1. Disconnect the power
to take out the ice
blocking the tray, then
connect the power
and press the POWER
button, the machine will
restart 3 minutes later.
2. Call customer service
The machine worked, but
the water got warm The solenoid is broken 1. Replace the solenoid
2. Call customer service
GB
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Innoliving INN-853 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Innoliving INN-853 in the language / languages: English, Italian as an attachment in your email.

The manual is 0.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info