768078

Inglesina Twin Sketch Manual

17
Zoom out
Zoom in
Previous page
1/96
Next page
17
EN
damp cloth and mild soap; do not use solvents, ammonia or
bleach.
Do not use abrasive cleaners or scrubbing pads.
• Follow the lining washing instructions on the labels.
Do not bleach
Do not tumble dry
Dry at in shade
Do not iron
Do not dry clean
Do not spin-dry
• Dry the textile lining completely before using or storing it.
LIST OF COMPONENTS
g. 1
A Hoods
B Handrails
C Storage baskets
OPENING THE STROLLER
g. 2 To open the stroller, release the hook (P1) that
ensures its folding and unbutton the 2 press studs (P2) that
hold the backrest of both seats to the structure.
g. 3 Holding the handle rmly on both sides, lift the
stroller until the correct opening click is heard.
REMOVING/ATTACHING THE FRONT WHEEL ASSEMBLIES
In case of need, the front wheel assemblies (D) can be easily
removed.
g. 4 To remove them, pull them out from the front
supports while holding down the lever (D1).
g. 5 To reinstall them, simply position them and push
until they clicks into place.
g. 6 Caution: make sure that the wheels are properly
attached before use.
REMOVING/ATTACHING THE REAR WHEELS
Should it be necessary, the rear wheels (E) can easily be
removed.
g. 7 To remove them, pull them out from the rear
support while holding down the button (E1).
g. 8 To reinstall them, simply position them and push
them until they click into place.
g. 9 Caution: make sure that the wheels are properly
attached before use.
REAR WHEELS BRAKE
g. 10 To operate the brake, use the rear lever (P3).
Always engage the brake during stops.
HANDRAIL
g. 11 Both handrails (B) can be open on one side or fully
removed; to open them, press the button (B1) and remove
them from their housings; to remove them, repeat the
procedure on the other side.
BACKRESTS ADJUSTING
g. 12 To lower the backrests, release the rear strap on
both by pressing the button (P4) on the central device (P5).
g. 13 To lift them, press the button (P4) on the central
device (P5) and simultaneously pull the rear ring (P6).
SAFETY BELTS
g. 14 Ensure that the safety belts are inserted in the slots
at the height of the shoulders or immediately above. If the
position is not correct, remove the belts from a pair of slots
and reinsert them in another one; always use the slots at the
same height.
g. 15 To move the back straps from one pair of slots to
the other, open the back zip (P7) on the backrest and remove
the back straps through the corresponding holes, on the
internal rigid reinforcement (P8).
g. 16 Then insert the back straps into the other pair of
slots on the backrest and pass through the corresponding
holes on the internal rigid reinforcement (P8).
g. 17 Make sure that the back strap is properly inserted
in the ends of the waist one (P9).
g. 18 Fasten the ends of the waist belt to the central
buckle (P10).
g. 19 Always use the crotch strap (P11) in combination
with the waist strap, making sure that they are all well
adjusted around the baby.
Caution! Failure to comply with this precaution can cause
the baby to fall or slide out, with serious injury risks.
Caution: adapt the height and the length of the harness
according to the baby’s growth.
HOODS
g. 20 To adjust the hoods, simply accompany them to
the desired position.
g. 21 The hood features a fabric insert that extends the
degree of cover, improving protection from the sun.
HOOD LININGS MAINTENANCE
The hood linings can be removed to allow for their correct
maintenance.
The lining removal way is the same for both hoods.
g. 22 To remove it, unbutton both rear press studs (A1).
g. 23 Unbutton the 2 press studs (A2) that x the hood to
the structure of the stroller and detach the side velcro (A3).
g. 24 Open the internal zip (A4) and free the lining from
the xed rear rib (A5).
g. 25 Use a screwdriver (or similar tool, not included)
to operate the lever (A6) placed on the hood joint and
simultaneously remove the front rib (A7) from its housing.
g. 26 Now remove the entire hood lining.
INSTRUCTIONS
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inglesina Twin Sketch at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inglesina Twin Sketch in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info