768091

Inglesina Newton 1.2.3 IFIX Manual

38
Zoom out
Zoom in
Previous page
1/196
Next page
38
EN
permitted height.
g. 41 Keeping the lever (E) in raised position, remove both shoulder strap
sections (G1) from the rear backrest rod (S1). Then remove them from the slots
on the child seats as well.
g. 42 Remove the adapter (H), removing the crotch strap (I3) from the inter-
leg protection.
g. 43 Remove the textile seat lining (S2) and temporarily remove the foam
lining (S3).
g. 44 Remove the crotch strap (I3) from the metal ring (I4).
g. 45 Remove the back straps from their metal ring as well (I5).
g. 46 Reposition and t the foam (S3) and textile (S2) linings correctly.
Place the complete harness in a safe place for future reuse.
UNIVERSAL CATEGORY - GR. 2/3 (15-36KG)
IFIX connectors and safety belts
INSTALLATION OF CHILD CAR SEAT IN VEHICLE
To install the child seat with the Ix connectors, follow the indications from
Fig. 02 to Fig. 10.
g. 47 Using the lever (F), bring the child seat to the completely vertical
position.
g. 48 Once the child seat is connected in the car using the Ix connectors
and after settling the child, use the rear lever (E), to adjust the height of the
headrest (A) to the desired position.
g. 49 The position of the car safety belt buckle can jeopardise the stability of
the child seat; if it is positioned as in gure, the child seat cannot be installed.
g. 50 Pass the diagonal section (T2) of the safety belt through the upper belt
guide (B) above the child’s shoulder.
g. 51 Then pass the lap section (T1) of the safety belt through the lower belt
guides (C) on both sides of the child seat and engage the belt in the housing
provided for that seat, until it CLICKS correctly into place.
Important: both sections of belt, lap and diagonal, must pass through the belt
guides at the connecting buckle.
g. 52 Ensure that the belt is always tight and not wound and, if necessary,
tighten it further by pulling the diagonal section (T2) upwards.
Caution! Make sure the safety belt is not twisted or caught on anything and that
the child seat’s lining does not obstruct its movement or prevent it from being
positioned correctly.
g. 53 Important! The upper belt guide (B) must always be positioned over
the child’s shoulders. The car’s safety belts must never be too low or too high
in relation to the child’s shoulders. To ensure the car’s safety belts are passed
correctly, periodically check and adjust the height of the backrest and the
headrest to adapt them as the child grows.
UNIVERSAL CATEGORY - GR. 2/3 (15-36KG)
Safety belts
INSTALLATION OF CHILD CAR SEAT IN VEHICLE
To install the child seat with ONLY the safety belts, follow the indications
from Fig. 47 to Fig. 53.
In this category, installation does NOT envisage the use of Ix connectors.
T
It
m
a
T
C
U
D
F
V
V
V
A
E
D
•
u
m
g
•
tr
•
s
•
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inglesina Newton 1.2.3 IFIX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inglesina Newton 1.2.3 IFIX in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 7,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info