769034
15
Zoom out
Zoom in
Previous page
1/56
Next page
15
Keep the vehicle in a dry place. If wet, dry the metal
parts to prevent rusting.
Excessive and prolonged exposure to sunlight and/or
rain may cause the fabric or plastic to fade or change
colour.
Periodically lubricate moving parts with light oil,
making sure the oil penetrates the mechanisms
deeply.
If the stroller has been used on the beach, clean it so
as to remove sand or salt from the mechanisms and
wheels.
Do not use bleach. Allow the stroller to dry completely
before using or storing it.
Follow upholstery washing instructions as shown on
the labels.
EN
Pushchairs and prams should be serviced after an
extended period of no use.
WARNING
WARNING: Make sure that the closing devices (E)
are properly hooked to the central joint as shown
in gure.
Only for chassis ERGO BIKE version: ADJUSTMENT
OF THE HANDLE
4 Press the push-buttons (F), positioned on both
sides of the handle, and rotate this latter upwards
simultaneously.
ASSEMBLY OF THE REAR WHEELS
5 WARNING: Two of the wheels supplied with
the chassis are equipped with a brake latch. These
two wheels (C) have to be assembled on the rear
axis of the chassis, near to the brake bar (G).
6 Make sure that the brake bar (G) is positioned
upwards (in brake release position).
7 Lift the chassis base (A) and hold one of the rear
wheels (C). Pull the hook (H) present on the wheel
upwards and then insert the wheel in the pin (I).
8 Push the wheel (C) towards inside and release
the hook (H) until hearing a click indicating that it has
hooked properly.
9 WARNING! Verify that the wheel is properly
hooked pulling it towards outside. Repeat the
same procedure also for the other rear wheel.
ASSEMBLY OF THE FRONT WHEELS
10_11 Lift the chassis base (A) and hold one of
the front wheels (B). Pull the hook (H) present on the
wheel upwards and insert the wheel in the pin (I).
LEGEND
A Chassis base
B Front wheels
C Rear wheels with brake latch
D Handle
E Chassis closing devices
F Handle adjustment push-buttons
(only for ERGO BIKE version)
G Brake bar
H Wheel closing hooks
(on all wheels)
I Wheel insertion pins
L Additional transport unit
hooking system
M Basket
N Safety lever
O Air pump
(only for ERGO BIKE version)
ASSEMBLY OF COMPONENTS
1 Check that all components of the chassis are
present: Chassis base (A), two front wheels (B), two
rear wheels (C), small air pump (only for ERGO BIKE
version).
HOW TO OPEN THE CHASSIS
2 Open the chassis base by pulling the handle (D)
upwards.
3 Press the handle (D) downwards until hearing
a CLICK indicating that both closing devices (E) have
been hooked.
INSTRUCTIONS
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inglesina Easy clip frame at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inglesina Easy clip frame in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info