549903
21
Zoom out
Zoom in
Previous page
1/57
Next page
20
Using the remote control
The remote uses two (2) AA batteries (not included). Install batteries by removing
the cover from the remotes back, aligning the + and - ends of the batteries, sliding
them into place, and then replacing the cover.
Caution:
When disposing of batteries, be sure to do so in an environmentally proper
manner.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Ensure the batteries’ polarity (+/-) is aligned correctly.
Do not mix new and old batteries together, or different types of batteries
together.
Replace the batteries as soon as they run out.
Remove the batteries from the remote control when storing or when the
remote will not be used for a prolonged period.
To operate, point the remote at the projector (not at the computer). The range of
optimum operation is about 30’ (9m).
Press the remote’s Power On and Off buttons to turn the projector on and off
(see
page 12 for shutdown information).
Press the remote’s Menu button to open the projector’s menu system. Use the
arrow buttons to navigate, and the Enter button to select features and adjust
values in the menus. See
page 23 for more information on the menus.
The remote also has:
•Focus button turns on the focus control.
Zoom button turns on the zoom control.
Test Pattern button toggles between different test patterns.
•Lens Shift button turns on the lens shift control.
•Exit closes the onscreen menus (page 23).
Input button to switch between sources.
•Picture button toggles between different picture modes.
•Network button displays network information.
Auto Sync button resynchronizes the projector to the source.
•Aspect button toggles between aspect ratios (see page 25).
•PiP button turns on the PiP feature.
•Overscan button toggles between overscan modes.
Freeze button freezes/unfreezes the source image being displayed.
Lamp Mode button toggles between single and dual lamp mode.
•- button is not used on this projector.
•Info. button displays projector and source information.
•Light button turns on the remote’s backlight.
•Clear button clears the ID Set entry information.
Shutter button to blank the screen.
•ID Set button allows the user to specify the remote and projector ID set. This
is helpful when more than one projector is used in a room. See the Setting an
ID Code for the Remote and Projector section on the next page.
POWER
ON
FOCUS ZOOM
LENS SHIFT
INPUT
AUTO SYNC
OVERSCAN
INFO. LIGHT
FREEZE
LAMP MODE
ASPECT PIP
PICTURE NETWORK
OFF
CLEAR SHUTTER ID SET
ENTER
MENU
1
4
789
5
23
6
EXIT
TEST
PATTERN
0
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for InFocus in5852L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of InFocus in5852L in the language / languages: English as an attachment in your email.

The manual is 12,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of InFocus in5852L

InFocus in5852L Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info