216221
34
Zoom out
Zoom in
Previous page
1/45
Next page
33
Using Network Functions (IN2114 & IN2116 only)
IMPORTANT: To enable network functions at all times (even when the pro-
jector is powered off), the Network item in the Always-On Functions sub-
menu in the Setup menu must be set to Yes (not No).
Projector network functions include:
Configuring and controlling the projector via a web browser.
Failure and warning alerts via email.
Projector Management via SNMP.
Controlling the projector via Scheduling.
NOTE: Projector web pages and emails sent by the projector are always dis-
played in English language.
Before using the network functions
To use the network functions of the projector, the projector must be config-
ured to suit your network. Consult with your network administrator before
connecting the projector to your network; incorrect network configuration
of the projector may cause problems on your network.
Connect the Network Cable
Properly connect projector to the network, then configure the following set-
tings.
If Using a Network with DHCP Enabled:
1 Use the projector's remote control or keypad to select the Network item
in the projector's Setup menu.
2 If DHCP is off, select it to turn it on.
If Using a Network that Does Not have DHCP Enabled:
1 Use the projector's remote control or keypad to select the Network item
in the projector's Setup menu.
2 If DHCP is on, select it to turn it off.
NOTE: If you still don’t see an IP address, go to the projector’s Setup menu,
select Network, then turn on Show Network Messages. After exiting the
menu press the Source button again.
3 Select IP Address. This will highlight the first of the four octets in the IP
address. Press Up or Down to change the value, then press Select or Right
when done to move to the next octet. Repeat until you have changed all
four octets in the IP address.
4 Repeat the above for Subnet Mask, Default Gateway, and other settings
that are in IP address format (to assign or change the Host Name, see
Network Settings Page below).
Configuring and Controlling the Projector via a Web Browser
You can adjust or control the projector via a network from a web browser
on a computer that is connected to the same network as the projector.
NOTES:
To access the projector’s web pages, the projector must be connected to
the network and connected to AC power (and if you want to access the
web pages even when the projector is powered off, make sure that the
Network item in the Always-On Functions submenu is set to Yes).
JavaScript must be enabled in your browser to use the projector web
pages properly. If JavaScript is disabled, see the Help files for your web
browser for details on how to enable it.
If no operations are performed in the web browser for approximately
ten minutes, the system will automatically log you off.
Logging in
To log into the projector web pages, follow these steps:
1 Make sure the projector is connected to the network and connected to
AC power.
2 If you don't know the projector's IP
address, turn on the projector. After the
projector starts up, if its IP address is not
shown, press the Source button to view the IP address.
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for InFocus in2114 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of InFocus in2114 in the language / languages: English as an attachment in your email.

The manual is 8,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of InFocus in2114

InFocus in2114 User Manual - German - 46 pages

InFocus in2114 User Manual - Dutch - 45 pages

InFocus in2114 User Manual - French - 45 pages

InFocus in2114 User Manual - Italian - 47 pages

InFocus in2114 User Manual - Swedish - 45 pages

InFocus in2114 User Manual - Spanish - 45 pages

InFocus in2114 Quick start guide - All languages - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info