Manual Indesit XWDE 861480 (page 13 of 84) (German, French, Polish)

577086

Zoom out

Zoom in

1/84

Troubleshooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make

sure that the problem cannot be solved easily using the following list.

Problem:

The washer-dryer does not switch

on.

The wash cycle does not start.

The washer-dryer does not fill

with water (the text “H2O” on the

display).

The washer-dryer continuously

takes in and drains water.

The washer-dryer does not drain

or spin.

The washer-dryer vibrates a lot

during the spin cycle.

The washer-dryer leaks.

The “option” and START/PAUSE

indicator lights flash rapidly and an

error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

Push & Wash does not activate.

The washer-dryer does not dry.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power in the house.

• The washer-dryer door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set.

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch the

appliance off and contact the Technical Assistance Service. If the dwelling is on one

of the upper floors of a building, there may be problems relating to water drainage,

causing the washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to prevent this inconvenience.

• The wash cycle does not include draining: some cycles require the draining

process to be enabled manually.

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washer-dryer is not level (see “Installation”).

• The washer-dryer is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care

and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text “for

washer-dryers” or “hand and machine wash”, or the like).

• Too much detergent was used.

• After switching on the machine a control other than Push&Wash+Dry was

activated. Switch the machine off and press the Push&Wash+Dry button.

• The appliance is not plugged into the socket, or not enough to make contact.

• There has been a power failure.

• The appliance door is not shut properly.

• A DELAY TIMER has been set.

• DRYING is in the OFF position.

despite reading the manual several times we cannot get a dry only cycle to work. its seems to run for 2 or 3 minutes then finishes Submitted on 14-8-2020 at 12:09
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Indesit XWDE 861480 in the language / languages: German, French, Polish as an attachment in your email.

The manual is 7,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Indesit XWDE 861480

Indesit XWDE 861480 User Manual - English, Dutch, Turkish - 56 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Indesit XWDE 861480 Manual

Product: