311804
2
Zoom out
Zoom in
Previous page
1/72
Next page
2
GB
Keep this instruction manual in a safe place for future
reference. Should the appliance be sold, transferred or
moved, make sure the instruction manual
accompanies the washing machine to inform the new
owner as to its operation and features.
! Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking
1. Unpack the machine.
2. Check whether the machine has been damaged
during transport. If this is the case, do not install it and
contact your retailer.
Remove the transit fixings
IMPORTANT: Follow these instructions to remove the
TWO transit fixings (see Description for location).
Situated on either side of the
rear panel,
BOTH transit boltsBOTH transit bolts
BOTH transit boltsBOTH transit bolts
BOTH transit bolts
MUST be rMUST be r
MUST be rMUST be r
MUST be r
emoved beforemoved befor
emoved beforemoved befor
emoved befor
e usee use
e usee use
e use.
! Failure to do so may cause
damage to your machine.
It is important the transit bolt
and spacer (see pic) come out
intact.
1. Unscrew the bolt using a
13mm spanner.
2. STOP when 3 threads can be
seen.
3. Hold, slide sideways and pull
to remove.
4. For safety, insert one of the
the plastic covers (supplied with
your machine) over the hole.
! Repeat steps 1 to 4 to remove
the second transit bolt.
! Packaging materials are not
children’s toys.
Levelling
Your machine will be noisy if the two front feet are not
adjusted so that the machine stands firm and level.
! The machine should be levelled from side to side and
from front to back.
1. Move your machine into its final location.
- Take care not to trap or kink
the hoses.
2. Turn one or both front feet
anti-clockwise by hand until the
feet cannot be turned any more.
When adjusting the feet, use a
spirit level to check the machine
stands level, from side to side
and from front to back.
- The spring on each foot will stop them coming loose.
! If it is placed on a fitted or loose carpet, adjust the
feet in such a way as to allow enough room for
ventilation beneath the machine.
Water connection
Connecting the water inlet hose.
Remember that this is a cold-fill machine.
! Check that seal is in place
inside the hose end cap.
Before making the water connections to gas ¾ thread,
allow the water to run freely from the supply tap until it
is perfectly clear.
Screw the inlet end with the blue
cap onto the cold water supply
tap.
Turn the taps on and check for leaks: tighten if
necessary.
! Make sure there are no kinks or bends in the hose.
! The water pressure at the tap must be within the
values indicated in the Technical details table (next
page).
! If the water inlet hose is not long enough, contact a
specialist store or an authorised serviceman.
! Always use new hoses.
! Check the water hose at least once a year, replace
any that are cracked as worn hoses could split under
water pressure.
Installation
WIXXL86-GB-indesit.p65 26/07/05, 14.152
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit wixxl 86 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit wixxl 86 in the language / languages: English as an attachment in your email.

The manual is 5,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info