4585
11
Zoom out
Zoom in
Previous page
1/84
Next page
11
Troubleshooting
Installation Description
Start and
Programmes Laundry
Warnings and
Suggestions
Maintenance and
Care Troubleshooting Service
GB
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Empty water light is flashing
but the dryer has only been
running for a short period.
Empty water light is on and
the water container is not full.
The ON/OFF light flashes to
indicate a fault.
Programme finishes and
clothes are damper than
expected.
Possible causes / Solution:
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
directly into the socket.
The door is not closed securely?
The PROGRAMMES knob has not been set properly (see Start and
Programmes).
The START button has not been pressed (see Start and Programmes).
You have set a delayed time (see Start and Programmes).
The filter has not been cleaned (see Maintenance).
The temperature setting is not ideal for the type of fabric you are drying
(see Start and Programmes, and see Laundry).
The water container needs emptying? The empty water light is flashing?
(see Maintenance).
The condenser needs cleaning? (see Maintenance).
The correct drying time has not been selected for the load (see Laundry).
The air intake grille or rear vents are obstructed (see Installation, and see
Maintenance).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
The water container was probably not emptied at the start of the programme.
Do not wait for the empty water signal, always check and empty the
container before starting a new drying programme (see Maintenance).
This is normal, the light flashes when the container is full. If the light is on
but not flashing it is just a reminder to empty the container (see Start and
Programmes).
If the ON/OFF light flashes together with the Time Delay and High Heat
lights; Or the ON/OFF light flashes together with the Time Delay, Alarm,
High Heat and Empty Water lights, then:
- Turn off and remove the plug. Clean the filter and the condenser
(see Maintenance). Then replace the plug, turn on and start another
programme. If the same combination of lights still flash contact the
Service Centre (see Service).
If any other combination of lights flash: Note down the other lights that
are on and contact the Service Centre (see Service).
! For safety the dryer has a maximum programme time of 3 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit ISL 70 CS (EX) at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit ISL 70 CS (EX) in the language / languages: Dutch as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info