127055

Indesit idl 75 eu 2 Manual

19
Zoom out
Zoom in
Previous page
1/76
Next page
16
GB
How to start the dishwasher
How to start a wash cycle…
After performing all the operations described in the previous chapters,
turn the water tap on completely, press ON-OFF button “A” situated
on the control panel and indicator light “B” comes on.
At this point, the dishwasher is on and ready to be programmed.
Starting and selecting the cycle.
Turn the cycle selector knob “D” clockwise until the reference notch
on the knob corresponds with the number or symbol for the cycle
you wish to set (consult the wash cycle table on page 17, especially
when first using the appliance).
If the appliance door is shut, press the Start button “R” and you will
hear a beep; the cycle will start up within a few seconds.
Cycle phase indicator lights
The dishwasher is provided with 4 indicator lights “G” which come
on in sequence as the appliance is performing that specific phase of
the wash cycle.
These phases are:
pre-wash, wash, rinses, drying
Cancelling or modifying a wash cycle in progress…..
Premise: You can cancel the wash cycle in progress, if it has only just
started.
To modify a wash cycle, keep the RESET button “R” pressed for
about 5 seconds: a prolonged beep will sound, followed by three
short beeps. Indicator light “G” will turn off and at this point, all the
settings will have been cancelled.
To select a new wash cycle, repeat the operations illustrated in the
paragraph entitled “starting and selecting the cycle”.
Warning: the knob must be turned clockwise from wash cycle 1 to
7, an anti-clockwise from wash cycle 7 to 1.
If you have left out a dish…
You can interrupt a wash cycle by pressing the ON- OFF button,
then place the dishes you had left out into the appliance, which will
start up from where it was interrupted when you turn it back on.
There’s been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity comes
back on or when the door is shut.
At the end of the wash cycle….
The end of the wash cycle is indicated by two short beeps and the
flashing of the drying phase indicator light.
• Turn off the water tap.
• Wait a few minutes before unloading the dishes: if you wait a little
while they dry better thanks to the steam.
• Empty the lower rack first.
Warning:when you open the dishwasher door after the wash cycle
has just ended or is under way, take care not to scald yourself with
the hot steam.
How to set the delayed start
When you have loaded the dishes, you can choose when to start
your dishwasher before setting the wash cycle desired. Press button
“H” to delay the start of the wash cycle by 12, 9, 6 or 3 hours. Each
time you press it, you will hear a short beep and the indicator light
“G” corresponding to the selected delay will light up.
Now you can select the desired wash cycle. Press the start button
“R” and after you hear the beep, the countdown to the delayed
start will begin.
Once this time is up, the indicator light will stop flashing and the
wash cycle will begin.
If you have set a 12 hour delay, for example, once you have selected
the wash cycle, the 12 hour indicator light will flash, followed by
the others in sequence until the set time delay is up. A quick look at
the indicator lights will keep you informed of the countdown progress
at all times.
Have you changed your mind?
If you change your mind, you can set a shorter time delay: press
button “H” to select it. You need not reset the wash cycle.
If on the other hand you want to cancel the delay set and you want
the cycle to start immediately, press button “H” repeatedly until the
cycle starts and indicator light “G” corresponding to the cycle start
phase comes on.
Dual function of indicator lights “G”
1) flashing to indicate a delayed start:to remind you that you
have set a delayed start;
2) on and not flashing beneath the cycle phase symbol:
meaning the cycle has started and is in the phase indicated by the
symbol.
You want to wash on one rack only?
Remember to use half the amount of detergent.
When you only have little cutlery to wash, you can run just half a
load on the upper rack, saving on water, detergent and electricity.
• When you press the “I” button, you will hear a blip and the “L”
indicator light will light up.
Once you have made your selection, start the wash cycle by pressing
Start and it will wash the top rack only.
- This option is available with all wash cycles.
- The Just You wash cycle is programmed to wash on the
upper rack only.
Warning:
Turn the appliance off by pressing button “A”, unplug the
appliance from the electricity socket to cut off the power
supply; the power supply cable should consequently be
easily accessible.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit idl 75 eu 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit idl 75 eu 2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info