123998
11
Zoom out
Zoom in
Previous page
1/80
Next page
11
EN
Troubleshooting
Malfunction: Possible causes / Solutions:
The dishwasher does not start.
The plug has not been inserted into the electrical socket
properly, or there is no power in the house.
The dishwasher door has not been shut properly.
 A delayed start has been programmed (see Start-up and use).
No water enters the dishwasher.
There is no water in the mains supply.
 The water inlet hose is bent (see Installation).
No water drains out from the
dishwasher.
The dishwasher cycle has not yet finished.
The water outlet hose is bent (see Installation).
The drain duct is blocked.
The filter is clogged up with food residues.
The dishwasher makes
excessive noise.
The dishes are rattling against each other or against the
sprayer arms.
The dishes and glasses are
covered in a white film or
limescale deposits.
The level of the refined salt is low or the dosage setting is not
suited to the hardness of the water (see Rinse aid and salt).
The lid on the salt dispenser is not closed properly.
The rinse aid has been used up or the dosage is too low.
The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish
tinge.
The rinse aid dosage is too high.
The crockery has not been dried
properly.
The rinse aid has been used up or the dosage is too low (see
Rinse aid and salt).
The rinse aid dispenser setting is not high enough.
A wash cycle without a drying programme has been selected.
The dishes are not clean.
The racks are overloaded (see Loading the racks).
The crockery has not been arranged well.
The sprayer arms cannot move freely.
The wash cycle is too gentle (see Wash cycles).
The detergent has not been measured out correctly or it is not
suited to the type of wash cycle (see Start-up and use).
The filter is dirty or blocked (see Care and maintenance).
The refined salt level is low (see Rinse aid and salt).
Tap shut-off alarm.
(several short beeps are emitted)
(the second and third WASH
CYCLE PHASE indicator lights
flash, beginning from the right).
Turn on the tap and the appliance will start after a few
minutes.
The appliance lock has been activated because no action was
taken when the beeps sounded. Switch off the machine using
the ON/OFF button, turn on the tap and switch the machine
back on after 20 seconds by pressing the same button. Re-
programme the machine and restart the wash cycle.
Clogged filter alarm
(the second and fourth WASH
CYCLE PHASE indicator lights
flash, beginning from the right).
Switch off the machine by pressing the ON/OFF button and
clean the filters (see Maintenance), then switch the
dishwasher back on by pressing the same button. Re-
programme the machine and restart the wash cycle.
Water loading solenoid
valve malfunction alarm
(the third WASH CYCLE PHASE
indicator light flashes, beginning
from the right).
Switch off the appliance by pressing the ON/OFF button and
switch it back on after a minute. If the alarm continues, shut
off the water tap to eliminate the risk of flooding, remove the
plug from the electrical socket and call Assistance.
Whenever the appliance fails to work, check for a solution from the following list before calling for Technical
Assistance Centre.
Some problems are indicated by one or two lights flashing rapidly: make a note of which lights are flashing before
calling Assistance.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit idl 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit idl 600 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info