127493

Indesit idl 557 fr2 Manual

19
Zoom out
Zoom in
Previous page
1/24
Next page
19
EN
Only use products that have been specifically designed
for dishwashers.
Do not use table salt or industrial salt.
If using a multi-functional product it is not
necessary to add rinse aid; however, we recommend that you
add salt, especially if you live in an area where the water is hard
or very hard. If you do not add salt or rinse aid, the LOW SALT*
and LOW RINSE AID* indicator lights will flash continuously.
Loading the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs
off surfaces more readily and therefore does not leave streaks
or marks.
The rinse aid dispenser should be filled:
• whenever the indicator light (H) signals that it is empty.
Illuminated light: add rinse aid; unlit light: there is no
shortage of rinse aid in the dispenser.
• when the LOW RINSE AID* indicator light on the panel
flashes;
1. Open the dispenser by turning
the lid (G) in an anticlockwise
direction.
2. Pour in the rinse aid, making
sure it does not overflow from the
dispenser. If this happens, clean
the spill immediately with a
sponge.
3. Screw the lid back on.
NEVER pour the rinse aid directly
into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver to
turn the dosage adjuster to one of the 6 pre-set positions (the
default position is set to 4):
• if there are white streaks on the crockery, set the adjuster to
a lower number (1-3).
• if drops of water remain on the crockery or there are
limescale marks present after the cycle has finished, set the
adjuster to a higher number (4-6).
If you are using multi-functional tablets and you wish to
further improve the drying performance of the appliance, fill the
dispenser and set the dosage adjuster to 2.
Loading the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the dispenser is never empty. Refined salt
removes limescale from the water, thus avoiding the formation of
deposits on crockery. The salt dispenser is located in the lower
part of the dishwasher (
see Description
) and should be filled:
• when the green float* cannot be seen by simply looking at
the cap of the salt dispenser;
• when the LOW SALT* indicator light on the panel
flashes;
• if your machine is not equipped with an indicator light or a
green float:
approximately every 30 wash cycles;
1. Remove the lower rack and
unscrew the cap of the dispenser (in
an anti-clockwise direction).
2. For the first wash cycle only: fill the
dispenser up to the edges with water.
3. Position the funnel provided
correctly (
see figure
) and fill the salt
dispenser up to the edges
(approximately 2 kg); it is normal for
a little water to leak out.
4. Remove the funnel, wipe away any salt residue from the
thread and screw the cap on tightly, so that detergent does
not leak into the dispenser during the wash cycle (this could
damage the water softening system beyond repair).
When salt has been added, run a wash cycle
immediately, without crockery, in order to remove any salt
solution that has leaked out and to avoid corrosion.
Adjusting the amount of salt*
It is possible to adjust the amount of salt used according to the
hardness of the water in your area (this information is available
from your local water board).
1. Unscrew the dispenser cap.
2. Turn the arrow on the neck of the
dispenser (
see figure
) towards the + or -
symbols, using the table below as a guide.
The default setting of the water softening system is +.
- If using multi-functional tablets fill the salt dispenser and set the
adjuster to -; if the hardness of the water is greater than 60°fH,
set it to +.
* Only available in selected models.
G
H
F
Rinse aid and refined salt
Hardness of the water
°dH °fH °mmol/l
Selector
knob
position
Salt
consumption
(grams/cycle)
Autonomy
(cycles/2 kg)
0 - 10 0 - 17 0 - 1.7 / 0 /
10 – 25
18 – 44
1.8 – 4.4
- 20 60
25 – 50
45 – 89
4.5 – 8.9
MED 40 40
> 50 > 89 > 8.9 + 60 25
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit idl 557 fr2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit idl 557 fr2 in the language / languages: English, French as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info