46874
7
Zoom out
Zoom in
Previous page
1/13
Next page
6
GB
Turning on the Appliance
First of all
Insert the plug into the electricity socket to power the
dishwasher. Turn on the water tap completely and press ON-
OFF button "A"; the display lights up and the wash cycle
time selected on the knob will flash.
Selecting and starting a wash cycle.
• Select the desired wash cycle by turning knob "D"
clockwise from wash cycle 1 to 7 and anticlockwise from 7
to 1; the display indicates the average duration of the wash
cycle and the cycle phases it consists of (consult the wash
cycle table contained on page 7, especially when first using
the appliance).
• Press the Start button "R" and the wash cycle starts up,
emitting a double beep; the approximate amount of time
left until the end of the wash cycle is displayed.
• If the time indicated at the start of the wash cycle does
not correspond to the actual duration of the cycle itself, this
could be for a number of reasons: the temperature of the
inlet water, the degree of soil, prolonged attempts by the
appliance to clean the wash filter from food residue clogging
it, etc.
Cycle phase under way indicator
While the wash cycle is under way, the symbols corresponding
to the cycle phases light up in sequence.
Here are the symbols corresponding to each cycle phase:
Pre-wash Wash Rinses Drying
Cancelling and modifying a wash cycle in progress
Premise: a wash cycle in progress can only be modified if it
hasn't been running for long.
Keep the Reset button "R" pressed for about 3 seconds:
a prolonged beep will sound, followed by three short beeps.
The cancelled cycle time will flash on the display. Turn the
knob to select a new wash cycle.
You've left out a dish?
You can interrupt a wash cycle by pressing the "ON-OFF"
button, then place the forgotten dishes into the appliance,
which will start up, after approximately 10 seconds, from
where it was interrupted when you turn it back on.
There's been a power failure? Has the dishwasher door
been opened?
The wash cycle stops and 3 dashes appear on the display;
the cycle restarts as soon as the electricity comes back on or
when the door is shut.
At the end of the wash cycle
The end of the wash cycle is indicated by two short beeps
and the word "END" flashes on the display.
• Turn the appliance off at the ON-OFF button
• Turn off the water tap.
• Empty the lower rack first.
Make sure the wash cycle has ended before removing the
dishes!
Warning: when you open the dishwasher door after the wash
cycle has just ended or is under way, take care not to scald
yourself with the hot steam.
How to set the extra drying
Press button "E". After a prolonged beep, indicator light
"G" lights up and the time corresponding to the wash cycle
selected on the knob will flash on the display.
Note: The time indicated on the display is extended due to
the extra drying time.
To disable the extra drying option, press the same button
and indicator light "G" will be turned off after a beep is
sounded.
This option is incompatible with the soak cycle.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit IDE1005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit IDE1005 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Indesit IDE1005

Indesit IDE1005 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info