Manual Indesit IDE1000 (page 11 of 13) (English)

46872

Zoom out

Zoom in

1/13

Cleaning and Special Maintenance

Troubleshooting

It may occur that the dishwasher does not function or does not

function properly. Before calling for assistance, let us see what can

be done first: have you forgot to press one of the buttons or to

perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient

pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you put the right amount of detergent into the dispenser?

Is the wash cycle suitable for the dishes you have placed inside the

appliance?

Are the filter and microfilter clean?

Can the sprayer arms turn freely?

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

If the display indicates the word "dON" when you turn your

dishwasher on, this means the demo mode is in operation.

Read the instructions on pages 7.

Error messages.

Your dishwasher is equipped with a safety system which is able to

detect any operating anomalies.

These anomalies or faults are signalled by several codes consisting of

letters and numbers that flash up on the display. Make a note of the

error code that appears, turn the appliance off, turn off the water

tap and call for technical assistance.

Tap off alarm

If you have forgotten to turn on the water tap, the appliance will

remind you with a series of prolonged beeps and the wording H2O

will flash up on the display. Turn the tap on and the wash cycle will

start up after a few minutes.

If you are not there when the H2O signal appears, the appliance will

switch to alarm mode and the code "A06" will flash on the display.

Turn the appliance off at button "A", turn on the water tap and wait

approximately 20 seconds before turning the appliance back on, the

wash cycle will start up again.

Clogged filter alarm

If the appliance is blocked and the code "A05" is flashing, this means

the filter is clogged by large particles of food residue. Turn the

appliance off at the ON-OFF button, clean the filter thoroughly and

reposition it in its seat, then turn the appliance back on. The wash

cycle will start up as normal after a few seconds.

Water load solenoid valve malfunction alarm

If the code "A02" flashes,

first of all turn off the water tap to avoid

any flooding and then cut off the electricity supply and call for

assistance.

If, despite all these checks, the dishwasher still does not function

and/or the problem persists, contact the nearest authorised service

centre and provide them with the following information:

- the nature of the problem;

- the model type number (Mod. ...) and the serial number (S/N ....),

which are indicated on the plate located on the side of the inner part

of the door.

Never call on unauthorised technicians and refuse to allow

parts to be installed that are not original spare parts.

The filter assembly

If you want consistent good results from your dishwasher, you need

to clean the filter assembly.

The food particles are removed from the wash water, allowing it to

be recirculated during the

cycle, filtered perfectly. For

this reason, it is a good idea

to remove the larger food

particles trapped inside the

semi-circular filter A and

cup “C”after each wash; to

remove the filter assembly,

pull the cup handle

upwards. All you need to do

is rinse them under running

water.

The entire filter assembly

should be cleaned

thoroughly once a month:

semi-circular filter A + cup

C + cylindrical filter B+

microfilter D.

To remove filter “B”, turn it anti-clockwise. Use a small non-metallic

brush for cleaning.

Reassemble the filter parts (as shown in the figure) and reinsert the

whole assembly into the dishwasher. Position it into its housing and

press downwards.

The dishwasher is not to be used without filters. Improper replacement

of the filters may reduce the efficiency of the wash and even damage

your dishwasher.

Cleaning the Sprayer Arms

It may happen that food particle become encrusted on the

sprayer arms and block the holes (see "Close up view

(interior)", letters F-I). Check the sprayer arms periodically

and clean them when needed.

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure 2 under

"Installation") located on the outlet of the water supply

tap. After turning off the water tap, unscrew the end of

the water supply hose, remove the filter and clean it carefully

under running water. Then, return the filter to its place and

tighten the water supply hose back into position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Indesit IDE1000 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Indesit IDE1000

Indesit IDE1000 User Manual - English - 80 pages

Indesit IDE1000 User Manual - English - 16 pages

Indesit IDE1000 User Manual - German, Dutch, French, Italian - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Indesit IDE1000 Manual

Product: