56001
43
Zoom out
Zoom in
Previous page
1/48
Next page
Important
It is essential that the lower cupboard is constructed in the manner illustrated i.e.
having side, back, and roof panels so joined as to provide no apertures which could
permit access to the oven unit when installed.
1. General
The appliance is designed for mounting at a safe level into an oven housing which
must be secured to the backing wall.
2. Ventilation
a. The oven housing unit cabinet dimensions must comply with fig. 4.
b. An air gap of 50mm minimum must be provided at the rear of any top or bottom
cupboards or shelves (see fig. 1).
c. It is necessary that the cabinets are provided with unobstructed ventilation, i.e.
from adjacent cabinetry. This can be done by either raising the base of the
cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in
the cabinet plinth to the dimensions in fig. 1.
d. The air gap at rear allows the warmed air to pass out of the inner cabinet space.
Where it is intended to fit cupboards above the oven unit to ceiling height, it is
essential that the warmed air is exhausted through the front of the cabinet
(see fig. 1).
e. If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven
when the door is opened could condense on and maybe stain the adjacent
surface. To prevent permanent staining, the adjacent surface should be made of a
material that is heat resisting and easy to clean. Adjacent tall cabinets should not
be deeper than the oven housing cabinet.
3. Final Installation
a. Using a spirit level, check that the housing cabinet is level from side to side and
from front to back in its installed position.
b. Correct any unevenness by placing spacers under the bottom of the cabinet.
Make sure that the cabinet rests firmly on the floor without rocking.
c. Before the oven is fitted, the cabinet must be firmly secured to the backing wall for
stability.
d. The oven unit should now be lifted (this is a two person lift) into the cabinet and
pushed fully home.
e. Finally, the oven is secured to the cabinet by means of the four Phillips C/SK Head
screws - two through each side trim.
f. Remove all packaging material from the grill and oven interior.
List of loose items:
4 x Phillips C/SK Head No. 6 x 25mm screws.
Installation
42
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit FID20 Mk2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit FID20 Mk2 in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info