46868
8
Zoom out
Zoom in
Previous page
1/16
Next page
6
GB
Turning on the Appliance
Starting a wash cycle ...
After performing all the operations described in the previous
paragraphs, turn the water tap on completely and press ON-
OFF button "A": you will hear a short beep and indicator
light "B" lights up. Now the appliance is on and ready to be
programmed.
Selecting a wash cycle …
To select the wash cycle, turn knob "D" clockwise until the
reference notch on the knob corresponds with the number
or symbol for the cycle you wish to set (have a look at the
wash cycle table on page 7). For a few seconds, the indicator
light "G" concerning the pre-wash cycle phase begins to
flash, then it stays permanently on without flashing for another
10 seconds approximately. During this time, you can modify
your choice of wash cycle. A short beep will indicate the
start of the wash cycle and indicator light "G" corresponding
to the cycle starting phase will light up.
After a few seconds, you will hear a short beep: the wash
cycle has begun and we do not recommend you change it.
Cycle phase indicator lights
The dishwasher is provided with 4 indicator lights "G" which
come on in sequence as the appliance is performing that
specific phase of the wash cycle.
These phases are:
pre-wash, wash, rinses, drying
Cancelling or modifying a wash cycle in progress…..
You can modify the wash cycle in progress, if it has only just
started. Turn the knob anti-clockwise until it reaches the Reset
position and, after a few seconds, you will hear 4 beeps and
indicator light "G" will turn off. This is to inform you that all
the settings have been cancelled.
You are now free to re-set the correct wash cycle.
If you have left out a dish…
You can interrupt the wash cycle by pressing the ON-OFF
button, insert the dish you had forgotten and press the ON-
OFF button again.
The cycle will start up from where you interrupted it.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
comes back on or when you shut the door.
At the end of the wash cycle….
The end of the wash cycle is indicated by two short beeps
and the flashing of the drying phase indicator light.
Turn the knob anti-clockwise to Reset in order to reset all
the settings.
Turn the appliance off to cut off the electricity supply.
Turn off the water tap.
Wait a few minutes before unloading the dishes: they are
very hot! If you wait a little while, they dry better thanks to
the steam.
Empty the lower rack first.
Make sure the wash cycle has ended before removing the
dishes!
Warning:
If opening the door soon after the end of the programme, or
during it, stand away from the Dishwasher, to avoid possible
injury from hot steam.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit DV620 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit DV620 in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info