46864
8
Zoom out
Zoom in
Previous page
1/16
Next page
6
GB
Turning on the Appliance
First of all....
After having completed all of the installation steps in the
preceding paragraphs, turn on the water to the unit and
press the ON-OFF button (A) located on the control panel.
The "B" indicator light will come on. At this point, the
appliance is on and ready to be programmed.
Starting and selecting the cycle...
Turn the cycle selector knob "D" until the reference notch
on the knob corresponds with the symbol for the cycle you
wish to set (have a look at the wash cycle table on page 7).
After a few seconds, you will hear a short beep and the
indicator light “G” comes on, indicating that the wash cycle
has begun and it is not advisable to make any changes at
this point.
Cycle phase indicator lights
The dishwasher is provided with 4 indicator lights "G" which
come on in sequence as the appliance is performing that
specific phase of the wash cycle.
These phases are, from left to right:
pre-wash, wash, rinses, drying
Cancelling or modifying a wash cycle in progress…..
Premise: You can cancel the wash cycle in progress, if it has
only just started.
To modify a wash cycle in progress, turn the knob anti-
clockwise and set it to Reset, after a few seconds you will
hear 3 beeps and indicator light "G" will go out: this means
all the settings have been cancelled. You are now free to re-
set the correct wash cycle.
If you forget to load some of the dishes...
The wash cycle can be interrupted by pressing the ON-OFF.
You can then load additional dishes and turn the appliance
back on. The cycle will start where it left off.
At the end of the wash cycle….
The end of the wash cycle is signalled by 2 short beeps and
a flashing drying phase indicator light “G”. Set the knob to
the Reset position to clear all settings.
Turn the appliance off by pressing button "A", thus cutting
off the electricity supply.
Turn off the water tap.
Wait a few minutes before unloading the dishes: they are
very hot! If you wait a little while, they dry better thanks to
the steam.
Empty the lower rack first.
Make sure the wash cycle has ended before removing the
dishes!
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
comes back on or when you close the door.
Warning: if opening the door soon after the end of the
programme,or during it, stand away from the Dishwasher,
to avoid possible injury from hot steam
Wash Cycle Adjustement Button
"1/2 LOAD" Button
This button (see "Close-up View - Control Panel", letter "N")
makes it possible to wash dishes using only the upper rack if
there are not enough dishes for a full load. This will allow
you to save on water and electrical energy.
It can be used before setting any of the wash cycles.
Please keep in mind that the amount of detergent should
also be cut in half.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Indesit DI67 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Indesit DI67 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info