697330
4
Zoom out
Zoom in
Previous page
1/8
Next page
EN
Contents
1x ACE (DARK) 12 V / 3 W
Dimensions 86x78x205mm (lxwxh)
1x ground stake
1x Easy-Lock
2x screws
2x plugs
1x Torx key
Material
Aluminium housing
High quality plastic lens
Please read the following instructions before installing. You are
advised to keep these installation instructions in a safe place.
Use
Above-ground lighting for use in gardens, or as lighting for
highlighting paths, patios or driveways.
Lamp
The xture is equipped with a high-quality LED lamp. These lamps
have a long life and a high light output and their power consumption
and the heat produced are extremely low.
Important!
Never connect the low-voltage cable directly to a 100-240 V power
source. It is only suitable for use in combination with a 12 V low-voltage
system. This product should only be used within the in-lite system. Use
of products other than those made by in-lite will invalidate the warranty.
Enjoy the lighting in your yard.
EN
Connecting the xture to 12 V
The already installed lamp means the xture is immediately ready for
use. Therefore you do not need to install the lamp rst.
General Installation Guideline
During installation, make sure that all components are easily
accessible for replacement.
Step 1
The xture can be mounted on a hard surface using the screws sup-
pliedor in soft surface using the ground stake supplied. The ground
stake is easily xed by screwing it in the underside of the base of the
xture.
When using on hard surfaces, rst remove the base of the xture by
loosening the Torx screw. (Fig. 1) Then x the base to the surface using
the accompany screws and possibly appropriate plugs. (Fig. 2) Place
the xture back on the base and tighten the Torx screw once again.
Step 2
Join the Easy-Lock connector to the main cable. (Fig. 3)
a. Clamp the cable duct on top of the main cable.
b. Place the cable duct (with the cable at the bottom) in the Easy-
Lock connector.
c. Tighten the threaded cap on the Easy-Lock connector. This will
cause the contacts to be pushed through the insulation on the
cable. In tightening the cap, a little gel is applied to the contacts in
the Easy-Lock connector. This serves to protect the contacts
against moisture. A little gel may possibly come out of the Easy-
Lock connector: so after installation (and/or before a meal), wash
your hands with soap and water, and avoid the gel coming into
contact with your eyes.
Step 3
Connect the main cable to the xture by connecting the mini-
connector. (Fig. 4)
If the lamp does not work correctly, check that the Easy-Lock connec-
tor is properly connected to the main cable. Do the same for the mini-
connector. Repeat steps 2 and 3. When the xture is connected to the
main cable also check that the contacts of the Easy-Lock connector
are not bent. If you have any problems, contact your dealer.
General maintenance advice
We advise wiping the xture down at least once a year using a clean
cloth and warm water.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for In Lite Ace at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of In Lite Ace in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info