493813
17
Zoom out
Zoom in
Previous page
1/21
Next page
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 170” Lower Cable (#59) to the opening on the bottom of the Leg
Developer (#9).
B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 3” Allen Bolt
(#76), two Pulley Bushings (#40), two Ø ¾” Washers (#79), and one M10 Aircraft
Nut (#82).
C.) Draw the Cable underneath the Pulley towards the back of the machine to the
opening on the Front Base Frame (#19). Install a Pulley with one M10 x 3 7/8”
Allen Bolt (#77), two 7/8” Pulley Bushings (#35), two Ø ¾” Washers (#79), and
one M10 Aircraft Nut (#82).
D.) Draw the Cable underneath the Pulley towards the back of the machine to the
Pulley Bracket (#18) underneath the Main Base Frame.
E.) Attach a Pulley to the Bracket. Secure it with one L-shaped Bracket (#23), one
M10 x 2” Allen Bolt (#65), two ¾” Washers (#79), and one M10 Aircraft Nut
(#82).
F.) Pull the Cable upward to the Angled Double Floating Pulley Brackets (#15)
previously installed in Step 6.
G.) Attach a Pulley to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#64),
two ¾” Washers (#79), and one M10 Aircraft Nut (#82).
H.) Draw the Cable around the Pulley then pull downward to the open bracket on the
Main Base Frame. Repeat Step G above to install another Pulley.
I.) Draw the Cable around the Pulley then pull upward to the Double Floating Pulley
Bracket (#14) previously installed in Step-5. Repeat Step G above to install a
Pulley.
J.) Draw the Cable around the Pulley then pull downward to the bracket on the rear
of Main Base Frame. Attach the Cable to a 6-Joint Chain (#29) using a Hook
(#32). Secure the other end of the Chain to the bracket with a M10 x 1” Allen
Bolt (#72), two ¾” Washers (#79) and one M10 Aircraft Nut (#82).
K.) Use the length of the Chain to adjust the tension of the Cable Loop System. If
the Cables are too loose, shorten the Chain.
L.) Attach the 15-Joint Chain (#31) to the end of the Cable by using a Hook. Attach
the Arm Curl Handle (#12) to the Chain by using another Hook. Replace Arm
Curl Handle with the Ankle Strap (#61) for various Leg exercises. Adjust the
length of Chain to obtain the desired exercise. Remove the Arm Curl Handle and
Ankle Strap when using the Leg Developer.
M.) Lubricate the two Guide Rods with WD-40 or light oil. This will minimize the
friction on the Rods so the weight plates can slide up and down on the rods more
freely.
16
Downloaded from www.Manualslib.com manuals search engine
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Impex MP 1105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Impex MP 1105 in the language / languages: English as an attachment in your email.

The manual is 2,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info