669827
36
Zoom out
Zoom in
Previous page
1/65
Next page
Receiver Auto‐Detection
A unique feature of the Vortex family of quadcopters is that the receiver type is auto-detected
by the OSD when running the wizard.
With the Vortex 250 Pro, it is no longer necessary to manually specify the receiver type with the
ImmersionRC Tools before running the wizard.
Note that occasionally the receiver detection fails, for reasons that are not yet understood. If
this is the case, force the receiver type using the Vortex Configurator chrome app.
R/C Transmitter Configuration
Version 1: OSD Firmware prior to 1.0.0.24
Depending upon the R/C transmitter in use, certain parameters need to be modified in order to
ensure compatibility with the Vortex 250 Pro, and more importantly with the Cleanflight Flight
Controller firmware.
In all cases, during the wizard setup, the current ‘PPM Value’ is shown on-screen beside each
control. This value must be as close as possible to a min. of 1000, center of 1500, and max. of
2000.
It is highly recommended to start with a ‘clean’ configuration (new model) for all radios.
Spektrum™ Radios
Spektrum radios need the following configuration:
- Two channels need reversing, AIL, and RUD.
- Map channel 5 to a 2 or 3-position switch to control flight mode (Acro/Horiz or
Acro/Level/Horiz).
- Verify that the endpoints are 1000/1500/2000 as described above.
FrSky Taranis Radio
- Map channel 5 to a 3-position switch to control flight mode (Acro/Level/Horiz).
- Verify that the endpoints are 1000/1500/2000 as described above.
Futaba S‐Bus Radios
- Map channel 5 to a 3-position switch to control flight mode (Acro/Level/Horiz).
- Reverse channels ELE and THR
- Change subtrim to -31 for THR, AIL, ELE, RUD
- Change travel to +/- 119 on all channels.
- Verify that the endpoints are 1000/1500/2000 as described above.
Version 2: OSD Firmware from 1.0.0.25 onwards
For 250 Pros with recent firmware, the wizard is much ‘smarter’, and is no longer as strict as
far as endpoints, and channel reversing goes.
36
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ImmersionRC Vortex 250 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ImmersionRC Vortex 250 Pro in the language / languages: English as an attachment in your email.

The manual is 3,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ImmersionRC Vortex 250 Pro

ImmersionRC Vortex 250 Pro Quick start guide - English - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info