504364
9
Zoom out
Zoom in
Previous page
1/21
Next page
OPERATIONAL INSTRUCTIONS
Headphones jack
The headphones PHONES jack (10) is for headphones with a 30- to 600-Ohm impedance, and
equipped with a 3.5mm jack. Use an adapter (sold in electronic outlets) if your headphone has a
dierent plug. The speakers are automatically switched o when the headphones are being used.
AM/FM radio operation
1. Turn the unit on by pressing
the POWER button (1)/(34).
2. Switch to the Tuner operating
mode by pressing the button
TUNER/BAND (23)/(56).
Manual station selection
1. Press button TUNER/BAND (23)/(56) repeatedly until the desired frequency band appears.
2. Press the buttons TUNING – or TUNING + (12)/(46) or (7)/(44) to tune to the desired radio
stations and have them indicated in the display (3).
3. Briey tapping the TUNING – or TUNING + button step by step alters the reception frequency
upward or downward.
Station search operation
1. Holding down one of the two buttons TUNING or TUNING + (12)/(46) or (7)/(44) for approx. 1 second
starts the search operation and determines the direction of the search. The search operation
simply nds stations with strong signals. Stations with weak reception can only be tuned
in manually.
2. Hold the TUNING – or TUNING + button to start the station search again. During the search
operation, the tuner is muted.
Amplier and Radio Operation - continued
CAUTION Listening at high volumes for an extended period of time may cause
damage to the users hearing.
OPERATIONAL INSTRUCTIONS
Amplier and Radio Operation - continued
Stereo / Mono
Repeatedly pressing the button
ST. / MONO (11) switches between
stereo and mono reception.
The stereo reception of a station
in the FM band is indicated
on the display (3)
In the case of stereo stations with a bad (noisy) reception, we recommend switching tuner to mono
reception. Press the ST. / MONO button. In the display (3), the message STEREO will disappear in
mono mode.
Tuner preset station
Each time the MEM./CLK ADJ. button (22)/(53) is pressed, the memory positions are called up one
after another in ascending number order.
The memory positions are selected directly using the numerical keys 1 - 0 / +10 (35) on the
remote control.
1. Program sites 1 – 9: Press the corresponding key 1- 9.
2. Program sites 10 – 19: Press button +10 and then the appropriate button 0 - 9.
3. Program site 20: Press button +10 twice and then the button 0.
Programming AM and FM stations in memory
The program memory allows you store 32 stations in FM and AM range. Program place selection is
described in the previous operating section.
1. In TUNER mode, select FM or
AM reception
2. Seek out the station required by
“Manual station selection or
“Station search operation
3. Press the MEM./CLK ADJ. (22)/(53)
and then press the REPEAT/PRESET
(8, front panel) or REPEAT/PRESET
(36, remote) until the desired memory preset appears.
iLuv | 16i9300 | V10M10_IM_EN_1111200815 | iLuv
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Iluv i9300D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Iluv i9300D in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info