ENGLISH 16
Installation
A If the appliance must be moved at any time, keep
it in an upright position; if absolutely necessary
onto its back.
Connecting the water supply
Adaptation of the water supply for installation should only be
performed by a qualied technician.
The water inlet and outlet hoses may be positioned towar
right or the left in order to achie
Make sure the dishwasher does not bend or squash the hoses.
Connecting the water inlet hose
• Run the water until it is perfectly clear
• Scre
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressur
T
properly
Make sure the hose is not bent or compr
Specications for the connection of the water
Water supply cold or hot (max. 60°C)
Water intake 3/4”
Power of water
Pressur
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
Supply hose:
Connecting the water outlet hose
Connect the outlet hose to a drain duct with a minimum
diameter of 2 cm A .
INSTALLATION
ENGLISH
A TTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary , it may be tilted onto
its back.
CONNECTING THE W A TER SUPPL Y
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE W A TER INLET HOSE
• Run the water until it is perfectly clear .
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
T e c h n i c a l Data table - otherwise the dishwasher may be function
properly .
Make sure the hose is not bent or compressed.
SPECIFICA TIONS FOR THE CONNECTION OF THE W A TER
SUPPL Y HOSE:
CONNECTING THE W A TER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A .
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B .
ANTI-FLOODING PROTECTION
Anti-flooding protection. T o ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop , which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
W ARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION) .
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door .
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SER VICE) . Do not use extension ca -
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised T echnical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
u n e v e n , the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly , it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher , stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con -
d e n s a t i o n which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
T o adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. T urn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAP ACITY :
MIN 40 cm
MAX 80 cm
W A TER SUPPL Y cold or hot (max. 60°C)
W A TER INT AKE 3/4”
POWER OF W A TER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAP ACITY 13 standard place-settings
The outlet hose connection must be at a height ranging fr
40 to 80 cm from the oor or surface wher
rests Befor
remoB .
Anti-ooding protection
Anti-ooding protection. T
dishwasher is pro
water supply in the event of anomalies or leaks fr
appliance.
Some models are also equipped with the supplementary safety
device Ne
even in the e
Model has Water pr
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
Electrical connection
W
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sur
that:
• The socket is earth and complies with current r
• The socket can
INSTALLATION
ENGLISH
A TTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary , it may be tilted onto
its back.
CONNECTING THE W A TER SUPPL Y
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE W A TER INLET HOSE
• Run the water until it is perfectly clear .
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
T e c h n i c a l Data table - otherwise the dishwasher may be function
properly .
Make sure the hose is not bent or compressed.
SPECIFICA TIONS FOR THE CONNECTION OF THE W A TER
SUPPL Y HOSE:
CONNECTING THE W A TER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A .
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B .
ANTI-FLOODING PROTECTION
Anti-flooding protection. T o ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop , which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
W ARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION) .
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door .
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SER VICE) . Do not use extension ca -
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised T echnical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
u n e v e n , the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly , it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher , stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con -
d e n s a t i o n which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
T o adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. T urn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAP ACITY :
MIN 40 cm
MAX 80 cm
W A TER SUPPL Y cold or hot (max. 60°C)
W A TER INT AKE 3/4”
POWER OF W A TER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAP ACITY 13 standard place-settings
withstand the maximum load of the
appliance as shown on the data plate located on the inside of
the door (see PRODUCT DESCRIPTION).
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SERVICE). Do not use extension cables
or multiple sockets. Once the appliance has been installed, the
power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it r
manufacturer or its authorised T
order to pr
The Company shall not be held responsible for any incidents, if
these regulations ar
Positioning and levelling
1. Position the dishwasher on a level sturdy oor
uneven, the fr
it reaches a horizontal position. If the appliance is le
correctly
or cause vibrations and noise while it is oper
2. Before r
transpar
it from any condensation which may form.
3. Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
4. T
bushing on the lower centr
dishwasher using a hexagonal spanner with an opening of 8
mm. T
height and in an anticlockwise direction to decr
Dimensions and capacity:
Width 598 mm
Height 820 mm
Depth 555 mm
Capacity 13 standard place-settings
