749835
12
Zoom out
Zoom in
Previous page
1/64
Next page
ENGLISH 12
ATTENTION: Always unplug the appliance when cleaning it and
when performing maintenance work. Do not use ammable
liquids to clean the machine.
Cleaning the dishwasher
Any marks on the inside of the appliance may be removed using
a cloth dampened with water and a little vinegar.
The external surfaces of the machine and the control panel
can be cleaned using a non-abrasive cloth which has been
dampened with water. Do not use solvents or abrasive products.
Preventing unpleasant odours
Always keep the door of the appliance ajar in order to avoid
moisture from forming and being trapped inside the machine.
Clean the seals around the door and detergent dispensers
regularly using a damp sponge. This will avoid food becoming
trapped in the seals, which is the main cause behind the
formation of unpleasant odours.
Cheking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If
damaged, replace it by a new hose available through our After-
Sales Service or your specialist dealer. Depending on the hose
type:
ENGLISH
10
Cleaning and maintenance
ATTENTION: Always unplug the appliance when cleaning it
and when performing maintenance work. Do not use flammable
liquids to clean the machine.
CLEANING THE DISHWASHER
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and
a little vinegar.
The external surfaces of the machine and the
control panel can be cleaned using a non-abrasive
cloth which has been dampened with water. Do
not use solvents or abrasive products.
PREVENTING UNPLEASANT ODOURS
Always keep the door of the appliance ajar in order to avoid mo-
isture from forming and being trapped inside the machine.
Clean the seals around the door and detergent dispensers regu-
larly using a damp sponge. This will avoid food becoming trapped
in the seals, which is the main cause behind the formation of
unpleasant odours.
CHEKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If dama-
ged, replace it by a new hose available through our After-Sales
Service or your specialist dealer. Depending on the hose type:
If the inlet hose has a transparent coating, periodically check if
the colour intensifies locall . If yes, the hose may have a leak and
should be replaced.
For water stop hoses: check the small safety valve inspection
window (see arrow). If it is red, the water stop function was trig-
gered, and the hose must be replaced by a new one.
For unscrewing this hose, press the release button while unscre-
wing the hose.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an exten-
ded period of time, let the water run to make sure it is clear and
free of impurities before performing the necessary connections. If
this precaution is not taken, the water inlet could become blocked
and damage the dishwasher.
CLEANING THE FILTER ASSEMBLY
Regularly clean the filter assembly so that the filters do not clo
and that the waste water flows away correctl .
Using dishwasher with clogged lters or foreign objects inside l-
tration system or sprayarms may cause unit malfunction resulting
in lose of performance, noisy work or higher resources usage.
The filter assembly consists of three filters which remove foo
residues from the washing water and then recirculate the water:
to obtain the best washing results, you need to keep them clean.
The dishwasher must not be used without lters or if the
lter is loose.
At least once per month or after each 30 cycles, check the filter
assembly and if necessary clean it thoroughly under running
water, using a non-metallic brush and following the instructions
below:
1. Turn the cylindrical filter A in an anti-clockwise direction and
pull it out (Fig 1).
2. Remove the cup filter B by exerting a slight pressure on the
side flaps (Fig 2).
3. Slide out the stainless-steel plate filter C (Fig 3).
4. In case you find foreign objects (such as broken glass, porc -
lain, bones, fruit seeds etc.) please remove them carefully.
5. Inspect the trap and remove any food residues. NEVER RE-
MOVE the wash-cycle pump protection (black detail) (Fig 4).
After cleaning the filters, replace the filter assembly and fix it
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
CLEANING THE SPRAY ARMS
On occasions, food residue may
become encrusted onto the
spray arms and block the holes
used to spray the water. It is
therefore recommended that you
check the arms from time to time
and clean them with a small
non-metallic brush.
To remove the upper spray arm,
turn the plastic locking ring in an
anti-clockwise direction.
The upper spray arm should be
replaced so that the side with
the greater number of holes is
facing upwards.
The lower spray arm may be
removed by pulling it upwards.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, conse-
quently preventing scale buildup on heater, contributing also to
better cleaning efficienc . This system regenerates itself with salt,
therefore it is required to refill salt container when empt . Frequen-
cy
of regeneration depends on water hardness level setting - by
default regeneration takes place once per 5 Eco cycles with water
hardness level set to 3. Regeneration process starts in final rins
and finishes in drying phase, before cycle ends
Single regeneration consumes: ~3.5L of water; takes up to 5 addi-
tional minutes for the cycle; consumes below 0.005kWh of energy.
A
A
B
C
12
34
If the inlet hose has a transparent coating, periodically check if
the colour intensies locall . If yes, the hose may have a leak and
should be replaced.
For water stop hoses: check the small safety valve inspection
window (see arrow). If it is red, the water stop function was
triggered, and the hose must be replaced by a new one. For
unscrewing this hose, press the release button while unscrewing
the hose.
Cleaning the water inlet hose
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it is
clear and free of impurities before performing the necessary
connections. If this precaution is not taken, the water inlet could
become blocked and damage the dishwasher.
Cleaning the lter assembly
Regularly clean the lter assembly so that the lters do not close
and that the waste water ows away correctl.
Using dishwasher with clogged lters or foreign objects inside
ltration system or sprayarms may cause unit malfunction
resulting in lose of performance, noisy work or higher resources
usage.
The lter assembly consists of three lters which remove foo
residues from the washing water and then recirculate the water:
to obtain the best washing results, you need to keep them clean.
The dishwasher must not be used without lters or if the
lter is loose.
At least once per month or after each 30 cycles, check the lter
assembly and if necessary clean it thoroughly under running water,
using a non-metallic brush and following the instructions below:
1. Turn the cylindrical lter A in an anti-clockwise direction
and pull it out (Fig 1).
2. Remove the cup lter B by exerting a slight pressure on the
side aps (Fig 2).
3. Slide out the stainless-steel plate lter C (Fig 3).
4. In case you nd foreign objects (such as broken glass,
porc - lain, bones, fruit seeds etc.) please remove them
carefully.
5. Inspect the trap and remove any food residues. NEVER
REMOVE the wash-cycle pump protection (black detail) (Fig
4).
21
43
A
C
A
B
After cleaning the lters, replace the lter assembly and x it
position correctly; this is essential for maintaining the ecient
operation of the dishwasher.
Cleaning the spray arms
On occasions, food residue may become encrusted onto the
spray arms and block the holes used to spray the water. It is
therefore recommended that you check the arms from time to
time and clean them with a small non-metallic brush.
To remove the upper spray arm, turn the plastic locking ring
in an anti-clockwise direction. The upper spray arm should be
replaced so that the side with the greater number of holes is
facing upwards.
The lower spray arm may be removed by pulling it upwards.
Water softening system
Water softener automatically
reduces water hardness,
consequently preventing
scale buildup on heater,
contributing also to better
cleaning ecienc . This
system regenerates itself with
salt, therefore it is required
to rell salt container
when empt . Frequency of
regeneration depends on
water hardness level setting -
by default regeneration takes
place once per 5 Eco cycles
with water hardness level set
to 3. Regeneration process
starts in nal rins and nishes
in drying phase, before cycle
ends Single regeneration consumes:
- ~3.5L of water;
- takes up to 5 additional minutes for the cycle;
- consumes below 0.005kWh of energy.
Cleaning and maintenance
12


Need help? Post your question in this forum.

Forumrules
1

Forum

ikea-rengora-404.755.72

Reset search

  • Question related to the dishwasher IKEA Rengo¨ra 404.755.72 - How to turn off the acoustic sound which the dishwasher plays when it finishes its job? No guidance is provided in the user manual of this particular version of Rengöra (in another version, with a different panel, there are instructions but not on this one). Thanks Submitted on 5-9-2024 at 09:48

    Reply Report abuse
  • Lo veo muy bajito...como se levanta hasta la meseta? Solo con las patas? Submitted on 23-5-2022 at 12:49

    Reply Report abuse
  • Hello
    I would like the notice in french please rengora 404 755 72
    thanks Submitted on 20-9-2021 at 08:50

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ikea Rengora 404.755.72 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ikea Rengora 404.755.72 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 18,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ikea Rengora 404.755.72

Ikea Rengora 404.755.72 User Manual - Dutch, Portuguese, Spanish - 64 pages

Ikea Rengora 404.755.72 Additional guide - All languages - 1 pages

Ikea Rengora 404.755.72 Installation Guide - All languages - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info