PORTUGUÊS 9
Certique-se de que a tampa está bem apertada para que não
entre detergente no depósito dur
(tal pode danicar o amaciador de água de modo irrepar
Assim que este procedimento estiver concluído, e
progr
de “
derramada
irremediavelmente os componentes em aço ino
A garantia não ser
tais circunstâncias.
Utilizeapenassalespecicamenteconcebidoparamáquinasde
lavar loiça. Se o depósito de sal não for enchido, o amaciador
deáguaeoelementodeaquecimentopodemserdanicados
em resultado da acumulação de calcário. A utilização de sal é
recomendada com qualquer tipo de detergente par
de lavar loiça.
Se for necessário adicionar sal, é obrigatório ex
o procedimento antes do início do ciclo de lavagem par
evitar corr
Deniradurezadaágua
Para que o amaciador de água funcione corr
é essencial que a denição de dureza da água tenha por base
a dureza da água e
informação consultando a empresa de abastecimento de água
local. O nível de dureza da água vem denido de fábrica.
• Ligue a máquina premindo o botão LIGAR/DESLIGAR.
• Desligue a máquina premindo o botão LIGAR/DESLIGAR.
• Mantenha premido o botão
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
durante 5 segundos, até ouvir
um sinal sonoro.
• Ligue a máquina premindo o botão LIGAR/DESLIGAR.
• O número do nível selecionado atualmente e o indicador
luminoso do sal cam intermitentes.
• Prima o botão
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
para selecionar o nível de dur
pretendido (ver a T
• Desligue a máquina premindo o botão LIGAR/DESLIGAR. A
denição está concluída!
T
Nível °dH
Graus
Alemães
°fH
Graus
Franceses
°Clark
graus
ingleses
1 Macia 0 - 6 0 - 10 0 - 7
2 Média 7 - 11 11 - 20 8 - 14
3 Média 12 - 16 21 - 29 15 - 20
4 Dura 17 - 34 30 - 60 21 - 42
5 Muito dur 35 - 50 61 - 90 43 - 62
Encher o distribuidor de abrilhantador
O abrilhantador facilita a SECAGEM da loiça. O distribuidor de
abrilhantador A deve ser enchido quando o indicador luminoso
de REABASTECIMENTO DO ABRILHANT
ENGLISH
7
Contr ol panel
Pr oduct description
1. Upper rack
2. �������
3. Upper rack height adjuster
4. Upper sprayer arm
5. Lower rack
6. Cutlery basket
7. Lower sprayer arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
1 1. Rating plate
12. Control panel
1
2
3
4
5
6
10
7
11
9
8
First use
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SAL T RESER VOIR
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine’ s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the
dishwasher (see PRODUCT DESCRIPTION) and should be
filled when the SALT REFILL indicator light in the
control panel is lit .
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
1. On-Of f/Reset button with indicator light
2. Program selection button
3. Salt refill indicator ligh
4. Rinse Aid refill indicator ligh
5. Program number and delay time indicator
6. T ablet indicator light
7. Display
8. Half Load indicator light
9. Half Load button
10. Delay button
1 1. ST AR T/Pause button with indicator light / T ab
1 2 3 4 5 6 7 8 9 10 11
3sec
h
no painel de
comandos se acender
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
BA
1. Abra o distribuidor
B
pressionando e puxando a patilha da tampa.
2. Encha cuidadosamente com abrilhantador até ao entalhe de
refer
derramá-lo. Se isso acontecer
pano seco.
3.
NUNCA deite o abrilhantador diretamente na cuba da máquina.
Ajustar a dosagem de abrilhantador
Se não estiver completamente satisfeito(a) com os resultados da
secagem, pode ajustar a quantidade de abrilhantador utilizado.
• Ligue a máquina de lavar loiça com o botão LIGAR/DESLIGAR.
• Desligue-a com o botão LIGAR/DESLIGAR.
• Prima o botão
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
três vezes - ser
• Ligue-a com o botão LIGAR/DESLIGAR.
• O número do nível selecionado atualmente e o indicador
luminoso do abrilhantador cam intermitentes.
• Prima o botão
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
para selecionar a quantidade de abrilhantador
a distribuir
• Desligue-a com o botão LIGAR/DESLIGAR.
A denição está concluída!
Se o nível de abrilhantador estiver denido para ZERO
será distribuído abrilhantador
ABRILHANT
É possível denir um máximo de 5 níveis, de acordo com o
modelo da máquina de lavar loiça. As denições de fábrica são
especícas deste modelo, pelo que dever
acima para utilizar corr
• Se a loiça possuir riscas azuladas, dena um nível baixo (1-2).
• Se existirem gotas de água ou mar
dena um número alto (3-4).
Encher o distribuidor de detergente
A utilização de detergentes que não foram concebidos
para máquinas de lavar loiça pode causar danos ou avarias
subsequentes no aparelho.
Para obter os melhor
secagem, é necessário usar uma combinação de detergente,
abrilhantador e sal. Recomendamos a utilização de detergentes
sem fosfatos ou cloro, uma vez que estes pr
para o meio ambiente. Os bons r
dependem da utilização da quantidade correta de detergente.
Ultrapassar a quantidade indicada não implica uma lavagem mais
ecaz e aumenta a
ajustada ao nível de
sujidade normal, utilize apr
(detergente líquido) e
diretamente na
Se a loiça estiver apenas ligeiramente suja ou tiver sido passada
por água antes de ser colocada na máquina de lavar loiça,
diminua a quantidade de detergente utilizado em conformidade
(mínimo de 20 g/ml),
gel ao interior da cuba.
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
D
C
Para abrir o distribuidor
de detergente, prima o
botão C.
Coloque o detergente
apenas no distribuidor
seco D
Coloque a quantidade de
detergente para pr
lavagem diretamente na
cuba.
1.
mencionadas anteriormente de modo a adicionar a
quantidade correta. Dentr D e
indicações para ajudar a dosear o detergente.
2. Elimine os r
distribuidor e feche a tampa até fazer clique.
3.
cima até que o dispositivo de fecho esteja xo no de
O distribuidor de detergente abre-se automaticamente no
momento certo, de acordo com o pr
detergentes tudo em um, recomendamos a utilização do botão
P
sempre obtidos os melhor
