110526
7
Zoom out
Zoom in
Previous page
1/14
Next page
5
Install/Replace Backup Battery
The iP99 uses a backup battery system to provide continuous alarm operation and clock settings
in the event of a power failure. If the Battery Low Icon located on the right of the display is on, it is
time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise
all settings may be lost during battery replacement.
Open the battery compartment cover located on the bottom of the unit. Insert 2 “AA” batteries
as indicated. We recommend the use of alkaline batteries for longer life.
Batteries information:
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium) batteries.
Replacing iP99 Backup Batteries
Using the iP99
Radio
Setting up Antennas
a)
Snap AM loop antenna into provided stand, then plug AM antenna cable into ƿ AM Loop Antenna socket on back of unit.
Move antenna away from unit for best reception.
b)
Extend ƾ FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas.
c) Locate iP99 and all antennas away from AC adaptor in wall socket (at least 3 feet) for best radio reception.
Tuning and Playing the Radio
a)
Press the Radio Button to select radio play mode. Press as needed to select FM or AM radio band.
b)
Turn the Set Wheel to tune radio to a desired station.
c)
To program the current station as a preset, press and hold Preset Button 1-2 until P1 flashes on display; press again for P2
and allow to time-out (beep confirmation). Repeat steps a,b,and c for other preset buttons to preset up to 12 stations (6 AM, 6
FM). To listen to a preset station at any time, simply press the desired preset button once or twice.
d)
Turn the Volume Wheel to adjust iP99 volume up or down.
e) Press the
EQ Button to select Treble, Bass, SRS WOW sound effect or Balance. Turn the Set Wheel to adjust settings. EQ
settings for iPhone/iPod and radio mode are independent.
f)
Press
Alarm Reset/Power Button to turn iP99 off.
Using the Line-in Jack
a)
You can play nondocking iPod models or other audio devices through the iP99 ƽ Line-in Jack, connect one end of a patch cord
(available at ihomeaudio.comin the device’s line out or headphones jack, the other in the iP99 line-in jack. Make sure there
is no iPhone/iPod docked in the iP99 when using the line-in jack.
b)
To listen to your audio device, press the Radio Button until “line-in” is displayed, indicating line-in mode. Adjust the output
volume on your line-in device.
Using Sleep Mode
Sleep mode lets you sleep to your iPhone/iPod or the radio, gradually lowering the volume until the unit shuts off at the selected
time.
a)
Press the Sleep Button to select an amount of time before the iP99 shuts off: 120, 90, 60, 30 or 15 minutes.
b)
Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting).
Using the Dimmer
a) Press the Snooze/Dimmer Button during normal operation to adjust brightness of LCD display. There are 8 levels of brightness
including OFF.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for IHome IP99 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of IHome IP99 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info