311701
13
Zoom out
Zoom in
Previous page
1/14
Next page
71
This appliance is equipped with safety functions
which detect faults at an early stage and react
appropriately.
Often, however, the faults detected are small
enough to be solved in a matter of minutes.
The appliance will not start, no lamp
lights up.
Check whether:
the appliance is plugged in;
the wall socket is functioning correctly (use a
table lamp or similar).
The appliance will not start, but the pilot
light is on.
Check whether:
the appliance lid is properly closed;
a programme has been selected;
the programme is started;
the water tap is open.
The appliance stops during the
programme.
Check whether:
the Rinse Hold button is pressed: terminate
this option;
the water tap is open;
the pump / foreign body trap are blocked (see
Removing the Foreign Body Trap);
Insufficient or no water supply.
Check whether:
the water tap is completely open, and the
water supply pressure is sufficient;
the water inlet hose is kinked;
the mesh filters are clogged (see
Maintenance and Cleaning/ Water Hose
Mesh Filters);
the water inlet hose is frozen.
Reselect the desired programme and start again
to continue with the programme (do not add
detergent for this programme).
The appliance does not drain out the
water.
Check whether:
drain hose is kinked (see Installation
Instructions);
the pump/ foreign body trap are blocked (see
Removing the Foreign Body Trap);
IMPORTANT:
Before draining, allow the wash
water to cool down.
the drain hose is frozen.
Reselect the desired programme and start again
to continue with the programme (do not add
detergent for this programme).
If the fault re-occurs, contact After-Sales Service
(see After-Sales Service).
the Rinse Hold button is pressed: terminate
this option.
Detergent and additive product residues
in dispenser at end of wash.
Check whether:
the siphon is correctly installed and clean
(see Maintenance and Cleaning/
Dispenser Cleaning Instructions);
enough water is being supplied. The mesh
filters could be clogged (see Maintenance
and Cleaning/ Water Hose Mesh Filters).
The appliance vibrates during the spin
cycle.
Check whether:
the appliance is level and solidly installed on
all feet (see Installation instructions);
the transport screws and transport bar have
been removed. Before starting up the
appliance, the transport screws and the
transport bracket must be removed
(see Installation instructions).
Final spin results are poor.
the appliance has an imbalance detection
and correction system. If individual heavy
articles are loaded (bathmat, bathrobe, etc.)
this system may reduce the spin speed
automatically to protect the appliance. It may
even interrupt the spin cycle altogether, if the
imbalance is too great after several spin
starts;
if the laundry is too humid at the end of the
cycle, add more articles of laundry to balance
the load and repeat the spin cycle;
excessive foam formation may prevent
spinning. Use less detergent.
Check whether:
the pump impeller is obstructed (see
Removing the Foreign Body Trap);
the lid was opened during the delicate or
wool programme. Close the lid and select a
spin programme.
TROUBLESHOOTING GUIDE
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ignis awv 508 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ignis awv 508 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis awv 508

Ignis awv 508 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info