462091
2
Zoom out
Zoom in
Previous page
1/14
Next page
GB 2
BEFORE USING THE WASHING MACHINE
1.Removing the packaging and inspection
After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use the
washing machine. Contact After-Sales Service or
your local retailer.
Check that the accessories and supplied parts are
all present.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
If the appliance was exposed to the cold before
delivery, keep it at room temperature for a few
hours before operating.
2.Remove the transport bolts
The washing machine is fitted with transport
bolts to avoid any possible damage to the interior
during transport. Before using the washing
machine, it is imperative that the transport bolts
are removed.
After their removal, cover the openings with the
4 enclosed plastic caps.
3.Install the washing machine
You are advised not to install the appliance in a
room where the temperature could drop to
below 0°C.
Given the weight of the appliance, attention must
be paid to safety standards when it is being moved.
When positioning the appliance, make sure that
the power cable is not kinked or compressed and
that it can be easily accessed if required.
Remove the protective film from the control
panel (if available on your model).
Move the appliance without carrying it by the
worktop.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
Make sure that all four feet are stable and resting
on the floor and then check that the washing
machine is perfectly level (use a spirit level).
In case of wooden or so-called “floating floors”
(for instance certain parquet or laminate floors),
place the appliance on a 60 x 60 cm sheet of
plywood at least 3 cm in thickness which is
secured to the floor.
If the washing machine is installed on a carpeted
floor, leave sufficient space between the
appliance and the floor to guarantee the free
circulation of air.
4.Water supply
Connect the water supply inlet hose in
accordance with the regulations of your local
water company.
Water supply: Cold water only (unless
otherwise indicated on
the programme chart)
Water tap: 3/4” threaded hose
connector”
Water pressure
(flow pressure): 100-1000 kPa (1-10 bar).
Use only new hoses to connect the washing
machine to the water supply. Used hoses must
not be used and should be discarded,
5.Drain
Connect the drain hose to the siphon or hook it
over the edge of a sink by means of the “U” bend
supplied.
If the washing machine is connected to an
integrated drainage system, ensure the latter is
equipped with a vent to avoid simultaneous
loading and draining of water (siphoning effect).
6.Electrical connections
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.
Voltage, power consumption and electrical
protection data are supplied on the inside of the
appliance door.
The washing machine must be connected
exclusively by means of a socket with an earth
connection in accordance with current
regulations. The washing machine must be
earthed by law. The manufacturer declines all
liability for possible damage to property or injury
to persons or pets deriving from failure to
observe the a/m directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing machine
disconnect it from the mains supply.
After installation, access to the mains plug or to
disconnection from mains supply must be
ensured at all times via a double-pole switch.
Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
Mains cable replacement is only to be carried out
by After-Sales Service.
Use the appliance only for domestic washing and
for its intended applications.
Minimum housing dimensions:
Width: 600 mm
Height: 850 mm
Depth: 600 mm
50120023GB.fm Page 2 Thursday, January 8, 2009 6:41 PM
Black process 45.0° 150.0 LPI
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ignis AWF 595 IG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ignis AWF 595 IG in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis AWF 595 IG

Ignis AWF 595 IG User Manual - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info