615948
29
Zoom out
Zoom in
Previous page
1/110
Next page
28
Using Autotest, the installation can be measured and tested in a simple and fast way. After
pressing the AUTOTEST key, LanTEK
®
II Cable Tester automatically performs a number of
pre-programmed single tests. Autotest can be enabled from the Display (DH) or Remote (RH)
handset.
Selection of single tests from the test series depends on the type of cabling to be tested.
Specification of the test series is based on approved or recommended standards, as well as
specific parameters.
After the test series is completed, LanTEK
®
II Cable Tester displays an overall passed/failed
result, as well as the individual passed/failed results.
Preferences on Display handset (DH)
Set Autotest Pref.
Select job folder.
Set cable name (cable ID).
Select cable type.
Connections
Separate cable line to be tested from all network components.
Using suitable patch cords, connect the Display handset (DH) to one end of the cable line
(link), and the Remote handset (RH) to the opposite end of the cable line (link).
Test run
By pressing the AUTOTEST key, the test procedures described below are initiated:
First, the Display handset (DH) attempts to establish a connection to the Remote handset
(RH) via a correctly connected wire pair. If connection cannot be established, the Display
handset (DH) will show the message "Searching for Remote (RH). The search is continued
until the Autotest is manually cancelled or the Remote handset (RH) is located.
After connection to the Remote handset (RH) has been successfully established, its serial
number is read out to check if current configuration data are available.
NOTE:
If during the last 7 days no calibration has been performed on the identified Remote
handset (RH), the Autotest is cancelled and the user receives a message that a field
calibration is required.
Display handset (DH) continues the Autotest if serial number is valid. Most Autotests start
with the Wiremap test for twisted pair cables.
Following the Wiremap test, the other single tests that have been defined for the currently
selected cable type are performed.
After completion of Autotest, all test data can be displayed, saved and printed.
The test results of the last Autotest are stored in the non-volatile memory and remain
available for viewing even after the LanTEK
®
II Cable Tester is powered on or powered
down.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ideal Networks LanTEK III at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ideal Networks LanTEK III in the language / languages: English as an attachment in your email.

The manual is 3,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info