670150
272
Zoom out
Zoom in
Previous page
1/282
Next page
20-4
20
CONNECTOR INFORMATION
[EXT KEYPAD] jack
The circuit is used to output memory content in 8 chan-
nel memories. You can output desired memory content
such as CW Memory keyer, Voice memory, RTTY/PSK
Memory to be transmitted. Push a switch to send the
memory information. Hold down the switch for 1 sec-
ond to repeatedly send the memory information.
When you connect the external keypad, turn ON the
following items in the Others set screen. (p. 15-16)
(SET [F-7] > OTHERS[F-5])
• External Keypad (Voice)
• External Keypad (Keyer)
• External Keypad (RTTY)
• External Keypad (PSK)
Mute switch: Mutes both transmission and reception
when the switch is turned ON.
[REF I/O] connector
This connector outputs or inputs a 10 MHz reference
signal.
• Input/Output impedance: 50
• Output level: Approximately –10 dBm
• Required input level: Approximately –10 dBm
• Output signal stability: ±0.05 ppm (0 ~ +50°C)
If you use an external reference signal,
set to “IN” in the “REF IN/OUT” item of the
ACC set screen.
You can adjust the internal Reference Signal frequen-
cy in the “REF Adjust” item of the ACC set screen.
(SET [F-7] > ACC [F-2] > REF Adjust)
[RELAY] jack
Goes to ground when transmitting to con-
trol an external non-Icom linear amplifier.
You can select either mechanical relay or
semi-conductor MOS-FET control.
Specifications
Mechanical relay (Reed Relay):
16 V DC/Less than 0.5 A
MOS-FET: Less than 250 V/ Less than 250 mA
You can change the control in the “SEND Relay Type”
item of the ACC set screen.
(SET [F-7] > ACC [F-2] > SEND Relay Type)
When the SEND terminal controls the inductive load
(such as a relay), a counter-electromotive force can
cause the transceiver’s malfunction or damage. To pre-
vent this, we recommend adding a switching diode,
such as an “1SS133, on the load side of the circuit to
the counter-electromotive force.
[X-VERTER] connector
You can connect your transverter unit
through the connector.
• Input/output impedance:
50
• Output level: Approximately –20 dBm or more
You can change the transverter function in the “Trans-
verter Function” item of the Others set screen.
You can also adjust the offset frequency in the “Trans-
verter Offset” item of the Others set screen.
(SET [F-7] > OTHERS [F-5] > Transverter Offset)
L
B
1.5kø
±
5%
1.5kø
±
5%
2.2kø
±
5%
4.7kø
±
5%
1.5kø
±
5%
1.5kø
±
5%
2.2kø
±
5%
4.7kø
±
5%
S1
S2
S3
S4
USER BOX
External Keypad
Mute switch
S5
S6
S7
S8
L
B
L
B
L
B
e SEND
u
15 V
ACC 1/2
sockets
Relay
Switching diode
To a
non-Icom
linear amplifier
[Example]
272


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC7850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC7850 in the language / languages: English as an attachment in your email.

The manual is 15,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info