670150
261
Zoom out
Zoom in
Previous page
1/282
Next page
18-13
18
CONTROL COMMAND
• Repeater tone/tone squelch frequency settings
Command: 1B 00, 1B 01
100Hz digit: 0–2
10 Hz digit: 0–9
1 Hz digit: 0–9
0.1 Hz digit: 0–9
Fixed digit: 0*
Fixed digit: 0*
q*
00X
XX
we
X
*Not necessary when setting a frequency.
• SSB transmission passband width settings
Command: 1A 050019, 050020, 050021
XX
Higher edge: 0=2500 Hz
1=2700 Hz
2=2800 Hz
3=2900 Hz
Lower edge: 0=100 Hz
1=200 Hz
2=300 Hz
3=500 Hz
• Antenna memory settings
Command: 1A 050292~050303
Data
Antenna selection
for TX for RX
00 ANT1
01 ANT2
02 ANT3
03 ANT4
04* ANT1 ANT4
05* ANT2 ANT4
06* ANT3 ANT4
*“RX” should be selected for ANT4.
• RIT frequency settings
Command: 21 00
10 Hz: 0–9
100 Hz: 0–9
1 Hz: 0–9
1 kHz: 0–9
XXXX XX
00: + (plus)
01: – (minus)
• Band edge frequency settings
Command: 02*, 1E 01, 1E 03
q
XXX
w ertyuio!0!1!2
XXXXXXX002DXXXXXXXX00
10 Hz digit: 0–9
1 Hz digit: 0–9
1 kHz digit: 0–9
100 Hz digit: 0–9
100 kHz digit: 0–9
10 kHz digit: 0–9
10 MHz digit: 0–6
1 MHz digit: 0–9
1000 MHz digit: 0 (fixed)
100 MHz digit: 0 (fixed)
10 Hz digit: 0–9
1 Hz digit: 0–9
1 kHz digit: 0–9
100 Hz digit: 0–9
100 kHz digit: 0–9
10 kHz digit: 0–9
10 MHz digit: 0–6
1 MHz digit: 0–9
1000 MHz digit: 0 (fixed)
100 MHz digit: 0 (fixed)
Separator (fixed)
Lower edge Higher edge
Edge number*: 01–30
*Edge number setting is not necessary with command 02.
• Codes for CW message contents
Command: 17 Up to 30 characters
To send CW messages, the following character codes
are used.
“FF” stops sending CW messages.
“^” is used to transmit a string of characters with
no inter-character space.
Transmit output power settings for transmit
output power limiting
Command: 1A 0A
X X X X X X X X
Frequency band code
01: 1.8 MHz 07: 18 MHz
02: 3.5 MHz 08: 21 MHz
03: 5 MHz 09: 24 MHz
04: 7 MHz 10: 28 MHz
05: 10 MHz 11: 50 MHz
06: 14 MHz
Output power limit
0005: 5 W~0200: 200 W
01: DATA OFF
02: DATA ON
Character ASCII code
0–9 30–39
A–Z 41–5A
a–z 61–7A
/ 2F
? 3F
. 2E
2D
, 2C
: 3A
Character ASCII code
27
( 28
) 29
= 3D
+ 2B
22
@ 40
Space 20
261


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC7850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC7850 in the language / languages: English as an attachment in your email.

The manual is 15,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info