670150
258
Zoom out
Zoom in
Previous page
1/282
Next page
18-10
18
CONTROL COMMAND
D Command table (continued)
Cmd. Sub Cmd. Data Description
1B
00 see p. 18-13 Send/read repeater tone frequency
01 see p. 18-13 Set/read TSQL tone frequency
1C
00 00 Send/read transceiver’s status (RX)
* When “CI-V Output (for ANT)” (Command:
1C 04) is set to “ON,” automatically outputs
when changed.
01 Send/read transceiver’s status (TX)
* When “CI-V Output (for ANT)” (Command:
1C 04) is set to “ON,” automatically outputs
when changed.
01 00 Send/read the antenna tuner OFF (through)
01 Send/read the antenna tuner ON
02 Send/read to tuning
02 00 Send/read transmit frequency monitor setting
OFF
01 Send/read transmit frequency monitor setting
ON
03 see p. 18-11 Read transmit frequency
* When “CI-V Output (for ANT)” (Command:
1C 04) is set to “ON,” automatically outputs
when changed.
04 00 Send/read command to disable to output the
antenna controller status (frequency and so
on) from [REMOTE]
01 Send/read command to enable to output the
antenna controller status (frequency and so
on) from [REMOTE]
1E 00 Read number of available TX frequency
band
01 see p. 18-13 Read TX band edge frequencies
02 Read number of user-set TX frequency band
03 see p. 18-13
Send/read user-set TX band edge frequencies
21 00 see p. 18-13 Send/read RIT frequency
01 00 or 01 Send/read RIT setting (00=OFF, 01=ON)
02 00 or 01 Send/read TX setting (00=OFF, 01=ON)
25 see p. 18-14 Send/read the Main or Sub band frequency
26 see p. 18-14 Send/read the selected operating mode and
filter
Cmd. Sub Cmd. Data Description
27 00 see p. 18-15 Read the Scope waveform data
* Only when “Scope ON/OFF status”
(Command: 27 10) and “Scope data output”
(Command: 27 20) are set to “ON,” outputs
the waveform data to the controller.
10 00 or 01 Send/read the Scope ON/OFF status
(00=Scope OFF, 01=Scope ON)
11 00 or 01
Send/read the Scope data output
(00=Output OFF, 01=Output ON)
* Only when “CI-V USB Port” is set to “Unlink
from [REMOTE]” and “CI-V USB Baud
Rate” is set to 115200 (bps), “Output ON” is
selectable.
12 00 or 01 Send/read the Main or Sub scope setting
(00=Main scope, 01=Sub scope)
13 00 or 01 Send/read the Single/Dual scope setting
(00=Single scope, 01=Dual scope)
14 see p. 18-15 Send/read the Scope Center mode or Fixed
mode setting
15 see p. 18-15 Send/read the span setting in the Center
mode Scope
16 see p. 18-15 Send/read the Edge number setting in the
Fixed mode Scope
17 see p. 18-15 Send/read the Scope hold function ON or
OFF
18 see p. 18-16 Send/read the Scope Attenuator setting
19 see p. 18-16 Send/read the Scope Reference level setting
1A see p. 18-16 Send/read the Sweep speed setting
1B 00 or 01 Send/read the Scope indication during TX in
the Center mode
(00=OFF, 01=ON)
1C 00 to 02 Send/read scope center frequency setting in
the Center mode
( 00=Filter center, 01=Carrier point center,
02=Carrier point center (Abs. Freq.))
1D see p. 18-16 Send/read the Scope VBW setting
1E see p. 18-16 Send/read the Scope Fixed edge frequencies
28 00 00 to 08 Transmits the Voice TX memory content
(00=T1 to 08=T8, 0x00=Cancel TX)
258


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC7850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC7850 in the language / languages: English as an attachment in your email.

The manual is 15,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info