670434
88
Zoom out
Zoom in
Previous page
1/96
Next page
16-1
[10.7 MHz OUT]
Outputs the 10.7 MHz IF signal for
an external detector/demodulator circuit.
• Center frequency: 10.7 MHz
• Band width*: 10 MHz
• Impedance: 50 Ω (unbalanced)
• Maximum output level:-10dBm (approximately)
*The band width is xed regardless of the digital PBT lter setting.
[REF I/O 10 MHz]
Outputs or inputs a 10 MHz
reference frequency signal.
You can change the signal direction
in the Set mode.
• Center frequency: 10 MHz
Impedance: 50 Ω (unbalanced)
Input/Output level: –10 dBm (approximately)
Frequency stability:
±0.5 ppm
(–10°C ~ +60°C, +14°F ~ +140 °F)
[I/Q OUT]
Outputs the Phase/Quadrature data which is
processed by the FPGA.
Connect a PC's USB port, to demodulate the DRM
broadcast or Software Dened Radio SDR.
Interface: USB (1.1/2.0), type B
L
Icom does not provide any support regarding SDR technology and
related software, except the inspection for the normality of output signal.
L The IQ driver and instruction guide will be released on the Icom
website near future.
http://www.icom.co.jp/world/index.html
[AF/IF]
Outputs the demodulate audio signal or 12 kHz IF
signal (unltered). The output level is xed, regardless
of the volume control position. (3.5 mm, 1/8 in (d))
Impedance: 4.7 kΩ
Output level: 100 ~ 300 mV (RMS)
LYou can select the output signal from AF or IF signals.
MENU
» SET > Connectors > AF/IF
LThe signal is also output from [USB] (front or rear) or [LAN].
[USB]
2 USB ports: Type B mini and Type B.
L You can download the USB driver and installation
guide from the Icom website.
http://www.icom.co.jp/world/support/download/rm
Outputs the decoded FSK (RTTY) signal, or D-STAR data.
Outputs the demodulated signal or 12 kHz IF signal.
Remote control interface for optional RS-R8600 (feature product).
Programming interface for the optional CS-R8600.
L You can change the port settings (FSK decode data/D-STAR data,
AF/IF), baud rate and output level)
MENU
» SET > Connectors > USB (Front)
MENU
» SET > Connectors > USB (Rear)
[LAN]
LED indication:
q
LINK/ACT Lights: Cable connected.
Doesn't light: Cable not connected.
Blinks: While the line is communicating.
w
Speed Lights: Communicating in 100BASE-TX
Doesn't lights: Communicating.
in10BASE-T, or not connected.
Time synchronization by an NTP server.
Outputs the demodulated signal or 12 kHz IF signal.
Remote control interface for the optional RS-R8600 (future
product).
LYou can select the output signal from AF and IF signals.
MENU
» SET > Connectors > LAN
[MUTE] JACK / [MUTE] SWITCH
Used to mute the receiver
output.
(3.5 mm, 1/8 in (d))
When the Mute Switch is slid to right, the receiver
enters to the Bit Error Rate (BER) Measurement mode
for the maintenance purpose.
When the [MUTE] is slid to left:
When this terminal is grounded, the receive circuit is turned OFF.
L Use this function when you use the IC-R8600 with a transceiver.
LThe sink current is approximately 1 mA at 8 V input.
When the [MUTE] is slid to right:
Connect a BER counter. In the BER Measurement mode,
the PN9 bit stream is output from this terminal.
[METER]
Connects to an external meter.
Outputs the received signal
strength or squelch level.
(3.5 mm, 1/8 in (d))
Output voltage: 8 V (maximum)
Output impedance: 10 kΩ
L You can select the output signal from received signal strength
and squelch levels.
MENU
»
SET > Connectors
q w
+
_
16
CONNECTOR INFORMATION
BNC type
BNC type
On the front panel
miniB type B type
On the rear panel
Meter output
Mute
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-R8600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-R8600 in the language / languages: English as an attachment in your email.

The manual is 22,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info