670434
82
Zoom out
Zoom in
Previous page
1/96
Next page
12-5
MAINTENANCE
12
Troubleshooting (Continued)
PROBLEM
POSSIBLE CAUSE SOLUTION REF.
The backlight is OFF.
The
indicator lights. (The
Panel Lock function is activated.)
Push to turn OFF the Panel
Lock function.
p. 3-3
The touch panel does
not work.
Programmed scan does
not start.
The same frequencies have been set
in scan edge memory channels.
Set different frequencies in scan edge
memory channels (P00A/P00B ~
P49A/P49B).
p. 8-2
Memory scan does not
start.
There is no entered memory
channel.
Enter at least 2 memory channels. p. 8-2
In the Memory mode, "BLANK" is
displayed instead of frequency.
Write a frequency to the blank channel. p. 8-2
Select memory scan
does not start.
0 or only 1 memory channel is
assigned as a Select channel.
Assign at least 2 memory channels as
Select channels.
p. 9-8
Cannot hear the speech
after pushing
.
The speech level is too low. Adjust the speech level in the Set
mode.
p. 11-3
The frequency readout
is blinking.
No external reference signal is input. Check the [REF I/O 10MHz] connector
setting or external signal source.
p. 11-7
“OVF” is displayed. An excessively strong signal is
received.
Set [RF GAIN] to a lower level. p. 3-1
Turn OFF the Preamp. p. 5-1
Turn ON the attenuator. p. 5-1
The touch screen is not
correctly working.
The touched point and the detected
point may be different.
Calibrate the touch screen. p. 12-3
Spectrum scope's
sensitivity is too low,
and only strong signals
are displayed.
The reference level is too low. Set the reference level to a higher
level.
p. 4-4
When selecting a
rmware le, "- No File
-" is displayed.
No rmware le is not found on the
SD card.
Copy the rmware le to the SD card. p. 13-2
The inserted SD card is not
formatted.
Format the SD card with the built-in
format function.
p. 7-2
The rmware le name has been
changed.
Download the rmware again. p. 13-1
FSK (RTTY) signal is
not demodulated.
The Mark or Space frequency is
incorrect.
Set the appropriate Mark and Space
frequencies.
p. 5-7
FSK (RTTY) signal
is received but not
decoded.
The shift setting is reversed. Select the FSK-R (Reverse) mode. p. 3-1
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-R8600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-R8600 in the language / languages: English as an attachment in your email.

The manual is 22,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info