670362
13
Zoom out
Zoom in
Previous page
1/48
Next page
9
2
PANEL DESCRIPTION
DTMF AUTODIAL KEY DTMA
Push to enter the DTMF channel selection mode. Then
select the desired DTMF channel using [CH Up]/[CH Down].
After selecting the desired DTMF channel, push this key to
transmit the DTMF code.
RE-DIAL KEY DTMR
Push to transmit the last-transmitted DTMF code.
CALL KEYS CALL/CALA/CALB
Push to transmit a 2/5-tone/BIIS ID code.
Call transmission is necessary before calling another station
depending on your signalling system.
[Call A] and/or [Call B] may be available when your system employs
selective Individual/Group calls. Ask your dealer which call is
assigned to each key.
EMERGENCY KEYS EMR
Push and hold for a specied period to transmit an emer-
gency call.
When [Emergency Single (Silent)] or [Emergency Repeat
(Silent)] is pushed, an emergency call is transmitted without
a beep emission and LCD indication change.*
If you want to cancel the emergency call, push (or push and
hold) the key again before transmitting the call.
The emergency call is transmitted one time only or repeatedly
until receiving a control code depending on the pre-setting.
*BIIS PMR operation only
SURVEILLANCE KEY SURV
Push to turn the surveillance function ON or OFF.
When this function is turned ON, the beep is not emitted and
the LCD backlight does not light when a signal is received or
a key is pushed, etc.
TX CODE ENTER KEY TXCE
(PMR or BIIS PMR operation only)
Push to enter the ID code edit mode directly, for both 5-tone
and BIIS. Then set the desired digit using [CH Up]/
[CH Down] or 10-keypad*. (p. 15)
*IC-F70DT/T or IC-F80DT/T only
TX CODE CHANNEL SELECT KEY TXC
Push to enter the ID code channel selection mode directly.
Then set the desired channel using [CH Up]/[CH Down].
(p. 14)
During ID code channel selection mode, push for 1 sec. to
enter the ID code edit mode for 5-tone and BIIS. Then set
the desired digit using [CH Up]/[CH Down] or 10-keypad*.
(p. 15)
*IC-F70DT/T or IC-F80DT/T only
TX CODE CHANNEL UP/DOWN KEYS TXCU/TXCD
Push to select a TX code channel directly.
2
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 9 (1,1)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-F80DT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-F80DT in the language / languages: English as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info