Manual Icom IC-F51 F61 (page 4 of 56) (English)

12516

Zoom out

Zoom in

1/56

INSTRUCTION MANUAL

UHF TRANSCEIVER

iF61

VHF TRANSCEIVER

iF51

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page A (1,1)

FOREWORD

READ ALL INSTRUCTIONS carefully and completely before

using the transceiver.

SAVE THIS INSTRUCTION MANUAL— This instruction

manual contains important operating instructions for the IC-F51

VHF

TRANSCEIVER

and IC-F61

UHF TRANSCEIVER

EXPLICIT DEFINITIONS

OPERATING NOTES

• When transmitting with a portable radio, hold the radio in a vertical

position with its microphone 5 to 10 centimeters away from your

mouth. Keep the antenna at least 2.5 centimeters from your head

and body.

• If you wear a portable two-way radio on your body, ensure that the

antenna is at least 2.5 centimeters from your body when transmit-

ting.

WORD DEFINITION

RWARNING

Personal injury, fire hazard or electric shock

may occur.

NOTE

If disregarded, inconvenience only. No risk

of personal injury, fire or electric shock.

CAUTION

Equipment damage may occur.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page i (1,1)

PRECAUTION

R WARNING! NEVER hold the transceiver so that the antenna

is very close to, or touching exposed parts of the body, especially

the face or eyes, while transmitting. The transceiver will perform

best if the microphone is 5 to 10 cm away from the lips and the

transceiver is vertical.

R WARNING! NEVER operate the transceiver with a headset

or other audio accessories at high volume levels.

CAUTION! NEVER short the terminals of the battery pack.

NEVER connect the transceiver to a power source other than the

BP-226 or BP-227. Such a connection will ruin the transceiver.

DO NOT push the PTT when not actually desiring to transmit.

AVOID using or placing the transceiver in direct sunlight or in

areas with temperatures below –25°C or above +55°C.

The basic operations, transmission and reception of the transceiver,

are guaranteed within the specified operating temperature range

(depending on version). However, the LCD display may be operate

correctly, or show an indication in the case of long hours of opera-

tion, or after being placed in extremely cold areas.

DO NOT modify the transceiver for any reason.

MAKE SURE the ﬂexible antenna and battery pack are securely

attached to the transceiver, and that the antenna and battery pack

are dry before attachment. Exposing the inside of the transceiver

to water will result in serious damage to the transceiver.

The use of non-Icom battery packs/chargers may impair transceiver

performance and invalidate the warranty.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page ii (1,1)

TABLE OF CONTENTS

iii

FOREWORD ……………………………………………………………… i

EXPLICIT DEFINITIONS ………………………………………………… i

OPERATING NOTES ……………………………………………………… i

PRECAUTION …………………………………………………………… ii

TABLE OF CONTENTS ………………………………………………… iii

SUPPLIED ACCESSORIES …………………………………………… iv

1 ACCESSORIES ……………………………………………………… 1–2

‘ Accessory attachments……………………………………………… 1

2 PANEL DESCRIPTION …………………………………………… 3–11

‘ Front, top and side panels ………………………………………… 3

‘ Function display ……………………………………………………… 6

‘ Programmable function keys ……………………………………… 7

3 CONVENTIONAL OPERATION ………………………………… 12–18

‘ Turning power ON ………………………………………………… 12

‘ Channel selection ………………………………………………… 12

‘ Call procedure ……………………………………………………… 13

‘ Receiving and transmitting ……………………………………… 14

‘ Scrambler function ………………………………………………… 17

‘ User set mode ……………………………………………………… 18

4 BIIS OPERATION ………………………………………………… 19–34

‘ Default setting ……………………………………………………… 19

‘ Receiving a call …………………………………………………… 20

‘ Transmitting a call ………………………………………………… 23

‘ Receiving a message ……………………………………………… 26

‘ Transmitting a status ……………………………………………… 29

‘ Transmitting an SDM ……………………………………………… 30

‘ Position data transmission ………………………………………… 31

‘ Printer connection ………………………………………………… 32

‘ PC connection ……………………………………………………… 32

‘ Digital ANI …………………………………………………………… 32

‘ Auto emergency transmission …………………………………… 33

‘ Stun function………………………………………………………… 33

‘ BIIS indication ……………………………………………………… 34

‘ Priority A channel selection ……………………………………… 34

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page iii (1,1)

5 BATTERY CHARGING ………………………………………… 35–44

‘ Battery charging …………………………………………………… 35

‘ Caution ……………………………………………………………… 36

‘ Optional battery chargers ………………………………………… 37

‘ Optional battery case ……………………………………………… 43

6 SPEAKER-MICROPHONE ……………………………………… 45–46

‘ Optional HM-138 description ……………………………………… 45

‘ Attachment ………………………………………………………… 46

7 OPTIONS ………………………………………………………… 47–48

8 DOC………………………………………………………………… 49–50

SUPPLIED ACCESSORIES

The following accessories are supplied: Qty.

• Flexible antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

• Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

• Jack cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 set

• Belt clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 set

• Function name stickers* (KEY-STICKER) . . . . . . . . . . . . . . . . . .1

*There are no names on the programmable function keys since the

functions can be freely assigned to [P0] to [P3], [Red], [ ] and

[ ] keys.

Attach the supplied function name stickers above the appropriate

keys for easy recognition of that key’s assigned function.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page iv (1,1)

ACCESSORIES

■ Accessory attachments

D Flexible antenna

Connect the supplied ﬂexible antenna

to the antenna connector.

CAUTION!

• NEVER HOLD by the antenna

when carrying the transceiver.

• Transmitting without an antenna

may damage the transceiver.

ï Battery pack

To attach the battery pack:

Slide the battery pack on the back of the transceiver in the direc-

tion of the arrow (q), then lock it with the battery release button.

• Slide the battery pack until the battery release button makes a ‘click’

sound.

To release the battery pack:

Push the battery release button in the direction of the arrow (w) as

shown below. The battery pack is then released.

Battery pack

Battery release button

NEVER release or at-

tach the battery pack

when the transceiver

is wet or soiled. This

may result in water or

dust getting into the

transceiver/battery

pack and may dam-

age the transceiver.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 1 (1,1)

ACCESSORIES

ï Jack cover

Attach the jack cover when the optional speaker-microphone is not

used.

D Belt clip

Attach the belt clip to the back of the transceiver with the supplied

screws.

Supplied screws

To attach the jack cover:

q Insert the jack cover into the

[SP MIC] connector.

w Tighten the screw.

To detach the jack cover:

e Unscrew the screw with a

phillips screwdriver.

r Detach the jack cover for the

speaker-microphone connec-

tion.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 2 (1,1)

PANEL DESCRIPTION

■ Front, top and side panels

NOTE: If the speaker netting (for dust prooﬁng) becomes wet,

dry it with a hair drier (cool mode) etc. before operating the

transceiver. Otherwise the audio may be difﬁcult to hear for

loss of the sound pressure.

Microphone

Function display

(p. 6)

Speaker

(See the following

NOTE.)

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 3 (1,1)

PANEL DESCRIPTION

q VOLUME CONTROL [VOL]

Turns power ON and adjusts the audio level.

w RED BUTTON

The desired function can be assigned by your dealer.

e ANTENNA CONNECTOR

Connects the supplied antenna.

r SPEAKER-MICROPHONE CONNECTOR [SP MIC]

Connects the optional speaker-microphone. (p. 46)

t DEALER-PROGRAMMABLE KEYS [P0] to [P3]

The desired functions can be assigned independently by your

dealer.

y CH UP AND DOWN KEYS [ ]/[ ]

➥ During standby condition, push to select an operating channel.

➥ After pushing [TX Code CH Select], push to select a TX code

channel.

➥ After pushing [DTMF Autodial], push to select a DTMF channel.

➥ After pushing and holding [Scan A Start/Stop]/[Scan B

Start/Stop], push to select a scan group.

➥ After pushing [Digital], push to select a BIIS code, status num-

ber or SDM.

*Desired functions can be assigned independently by your dealer.

☞ Continue to the next page.

[SP MIC] jack cover

NOTE: KEEP the [SP MIC]

jack cover attached to the

transceiver when the speaker-

microphone is not used.

(See p. 2 for details)

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 4 (1,1)

PANEL DESCRIPTION

■ Front, top and side panels (Continued)

u TRANSMIT/BUSY INDICATOR

Lights red while transmitting; lights green while receiving a sig-

nal, or when the squelch is open.

i PTT SWITCH [PTT]

Push and hold to transmit; release to receive.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 5 (1,1)

PANEL DESCRIPTION

■ Function display

q OUTPUT POWER INDICATOR

Appears when Low 2 or Low 1 is selected.

w AUDIBLE INDICATOR

➥ Appears when the channel is in the ‘audible’ (unmute) condi-

tion.

➥ Appears when the speciﬁed 5-tone/BIIS code is received.

e COMPANDER INDICATOR

Appears when the compander function is activated.

r KEY LOCK INDICATOR

Appears during the key lock function ON.

t SCRAMBLER INDICATOR

Appears when the voice scrambler function is activated.

y BELL INDICATOR

Appears/Blinks when the speciﬁc 5-tone/BIIS code is received,

according to the programming.

u BATTERY INDICATOR

Appears or blinks when the battery power decreases to a speci-

ﬁed level.

i ALPHANUMERIC DISPLAY

Displays the operating channel number, channel names, Set

mode contents, DTMF numbers, etc.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 6 (1,1)

PANEL DESCRIPTION

■ Programmable function keys

The following functions can be assigned to [P0], [P1], [P2], [P3],

[Red], []and []programmable function keys.

Consult your Icom dealer or system operator for details concerning

your transceivers programming.

If the programmable function names are bracketed in the following

explanations, the speciﬁc switch used to activate the function de-

pends on programming.

CH UP AND DOWN KEYS

• Select an operating channel.

• Select a transmit code channel after pushing the [TX Code CH

Select] keys.

• Select a DTMF channel after pushing the [DTMF Autodial] key.

• Select a scan group after pushing and holding the [Scan A

Start/Stop]/[Scan B Start/Stop] keys.

• Select a BIIS code, status number or SDM after pushing the

[Digital] key.

BANK SELECT KEY

Push this key, then push [CH Up] or [CH Down] to select the de-

sired bank.

SCAN START/STOP KEYS

➥ Push this key to start scanning; and push again to stop.

➥ Push and hold this key to indicate the scan group, then select

the desired scan group using [CH Up]/[CH Down].

SCAN TAG KEY

Adds or deletes the selected channel to the scan group.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 7 (1,1)

PANEL DESCRIPTION

PRIORITY CHANNEL KEYS

➥ Push to select Priority A or Priority B channel.

➥ Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel.

MR-CH 1/2/3/4 KEYS

Select an operating channel directly.

MONITOR KEY

Activates one of (or two of) the following functions on each channel

independently:

• Push and hold to un-mute the channel (audio is emitted; ‘Audible’ con-

dition).

• Push to mute the channel (sets to ‘Inaudible’ only).

• Push to un-mute the channel (sets to ‘Audible’ only).

• Push after the communication is ﬁnished to send a ‘reset code’.

NOTE: The un-mute condition (‘Audible’ condition) may auto-

matically return to the mute condition (‘Inaudible’ condition) after

a speciﬁed period.

LOCK KEY

Push and hold to electronically lock all programmable keys except

the following:

[Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys.

OUTPUT POWER SELECTION KEY

Select the transmit output power temporarily or permanently, de-

pending on the pre-setting.

• Ask your dealer for the output power level for each selection.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 8 (1,1)

PANEL DESCRIPTION

C.TONE CHANNEL ENTER KEY

Select the continuous tone channel using [CH Up]/[CH Down] keys

to change the tone frequency/code setting after pushing this key for

permanent operation.

TALK AROUND KEY

Turn the talk around function ON and OFF.

• The talk around function equalizes the transmit frequency to the re-

ceive frequency for transceiver-to-transceiver communication.

WIDE/NARROW KEY

Push to toggle the IF bandwidth between wide and narrow.

• The wide passband width can be selected from 25.0 or 20.0 kHz using

the CS-F50

CLONING SOFTWARE

. Ask your dealer for details.

DTMF AUTODIAL KEY

➥ Push to enter the DTMF channel selection mode. Then select

the desired DTMF channel using [CH Up]/[CH Down] keys.

➥ After selecting the desired DTMF channel, push this key to trans-

mit the DTMF code.

DTMF RE-DIAL KEY

Push to transmit the last-transmitted DTMF code.

CALL KEYS

Push to transmit a 5-tone/BIIS ID code.

• Call transmission is necessary before you call another station de-

pending on your signalling system.

• The [Call A] and/or [Call B] keys may be available when your system

employs selective ‘Individual/Group’ calls. Ask your dealer which call is

assigned to each key.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 9 (1,1)

PANEL DESCRIPTION

EMERGENCY KEYS

➥ Push and hold to transmit an emergency call.

➥ When [Emergency Single (Silent)] or [Emergency Repeat

(Silent)] is pushed, an emergency call is transmitted without a

beep emission and LCD indication change.

• If you want to cancel the emergency call, push (or push and hold)

the key again before transmitting the call.

• The emergency call is transmitted one time only or repeatedly until

receiving a control code depending on the pre-setting.

TX CODE ENTER KEY

Push to enter the direct ID code edit mode, for both 5-tone and

MSK. Then set the desired digit using [CH Up]/[CH Down]/

[TX Code CH Up]/[TX Code CH Down]. (p. 16)

TX CODE CHANNEL SELECT KEY

➥ Push to enter the direct ID code channel selection mode. Then

set the desired channel using [CH Up]/[CH Down]/[TX Code CH

Up]/[TX Code CH Down]. (p. 15)

➥ While in ID code channel selection mode, push for 1 sec. to enter

the ID code edit mode. Then set the desired digit using [CH

Up]/[CH Down]/[TX Code CH Up]/[TX Code CH Down]. (p. 16)

TX CODE CHANNEL UP/DOWN KEYS

Push to select a TX code channel directly.

ID MEMORY READ KEY

➥ Recalls detected ID codes.

• Push this key, then push [CH Up]/[CH Down] for selection.

• Up to 5 ID’s are memorized.

➥ Push and hold to erase the selected memorized ID’s.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 10 (1,1)

PANEL DESCRIPTION

VOICE SCRAMBLER FUNCTION

Push to toggle the voice scrambler function ON and OFF.

COMPANDER KEY

Push to toggle the compander function ON and OFF.

The compander function reduces noise components from the trans-

mitting audio to provide clear communication.

USER SET MODE KEY

➥ Push and hold to enter user set mode.

• During user set mode, push this key to select an item, and push

[CH Up]/[CH Down] to change the value or condition.

➥ Push and hold this key again to exit user set mode.

• User set mode is also available via the ‘Power ON function’. Please

refer to p. 18 also.

DIGITAL KEY (BIIS operation only)

➥ Push to select the call ID list, transmit message and standby

condition. Toggles between queue channel and received mes-

sage record indication after queue channel is selected.

➥ Push and hold to select queue channel indication.

STATUS UP/DOWN KEYS (BIIS operation only)

➥ While in the standby condition, push to display the transmit sta-

tus indication and select a status number.

➥ When a received SDM is displayed, push to cancel the automatic

scroll and scroll the message manually.

➥ When an SDM that contains more than 8 characters is displayed,

push to scroll the message manually.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 11 (1,1)

CONVENTIONAL OPERATION

■ Turning power ON

q Rotate [VOL] to turn power ON.

w If the transceiver is programmed for a start up passcode, input

digit codes as directed by your dealer.

• The keys in the table below can be used for password input:

• The transceiver detects numbers in the same block as identical.

Therefore “01234” and “56789” are the same.

e When the “PASSWORD” indication does not clear after inputting

4 digits, the input code number may be incorrect. Turn the power

off and start over in this case.

■ Channel selection

Several types of channel selections are available. Methods may dif-

fer according to your system set up.

NON-BANK TYPE:

Push [ ]/[ ] to select the desired operating channel, in se-

quence; or, push one of the [MR-CH 1] to [MR-CH 4] keys to select

a channel directly.

BANK-TYPE:

Push [Bank], then push [ ] or [ ] to select the desired bank.

AUTOMATIC SCAN TYPE:

Channel setting is not necessary for this type. When turning the

power ON, the transceiver automatically starts scanning. Scanning

stops when receiving a call.

KEY

NUMBER

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 12 (1,1)

CONVENTIONAL OPERATION

■ Call procedure

When your system employs tone signalling (excluding CTCSS and

DTCS), the call procedure may be necessary prior to voice trans-

mission. The tone signalling employed may be a selective calling

system which allows you to call speciﬁc station(s) only and prevent

unwanted stations from contacting you.

q Select the desired TX code channel or 5-tone code according to

your System Operator’s instructions.

• This may not be necessary depending on programming.

• Refer to pgs. 15, 16 for selection.

w Push the call switch (assigned to one of the dealer programma-

ble switches: [P0], [P1], [P2], [P3], [Red], []and []).

e After transmitting a 5-tone code, the remainder of your commu-

nication can be carried out in the normal fashion.

Selective calling

Non-selective calling

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 13 (1,1)

CONVENTIONAL OPERATION

■ Receiving and transmitting

NOTE: Transmitting without an antenna may damage the trans-

ceiver. See p. 1 for antenna attachment.

Receiving:

q Rotate [VOL] to turn power ON.

w Push [ ] or [ ] to select a channel.

e When receiving a call, adjust the audio output level to a comfort-

able listening level.

Transmitting:

Wait for the channel to become clear to avoid interference.

q While pushing and holding [PTT], speak into the microphone at a

normal voice level.

• When a tone signalling system is used, the call procedure de-

scribed at left may be necessary.

w Release [PTT] to return to receive.

IMPORTANT: To maximize the readability of your signal;

1. Pause brieﬂy after pushing [PTT].

2. Hold the microphone 5 to 10 cm from your mouth, then speak

into the microphone at a normal voice level.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 14 (1,1)

CONVENTIONAL OPERATION

D Transmitting notes

• Transmit inhibit function

The transceiver has several inhibit functions which restrict trans-

mission under the following conditions:

- The channel is in mute condition (‘Inaudible’ condition; “ ”

does not appear).

- Channel is busy.

- Un-matched (or matched) CTCSS is received.

- The selected channel is a ‘receive only’ channel.

• Time-out timer

After continuous transmission for the pre-programmed time period, the

time-out timer is activated, causing the transceiver to stop transmitting.

• Penalty timer

Once the time-out timer is activated, transmission is further inhibited

for a period determined by the penalty timer.

D TX code channel selection

If the transceiver has [TX Code CH Select] assigned to it, indica-

tion can be toggled between the operating channel number (or

name) and TX code channel number (or name). When the TX code

channel number (or name) is displayed, the [ ]/[ ] key selects

the TX code channel.

TO SELECT A TX CHANNEL:

q Push [TX Code CH Select]— a TX code channel appears.

w Push [ ]/[ ] to select the desired TX code channel.

e Push [Call] (or [PTT] during MSK operation) to transmit the se-

lected TX code.

r Push [TX Code CH Select] again to return to the operating chan-

nel number indication.

FOR TX CODE CHANNEL TYPE:

If the transceiver has a [TX Code CH Up] or [TX Code CH Down]

key assignment, the programmed TX code channel can be selected

directly.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 15 (1,1)

CONVENTIONAL OPERATION

D TX code number edit

If the transceiver has [TX Code CH Select] or [TX Code Enter] as-

signed to it, TX code contents can be edited within the allowable

digits.

TO EDIT A TX CODE VIA [TX CODE CH SELECT] KEY:

q Push [TX Code CH Select] to enter the TX code channel selec-

tion mode.

• Select the desired channel using [ ]/[ ] if necessary.

w Push [TX Code CH Select] for 1 sec. to enter the TX code edit

mode.

e Push [TX Code CH Select] to select the desired digit to be

edited.

r Set the desired digit using [ ]/[ ]/[TX Code CH Up]/[TX

Code CH Down].

t Push [TX Code CH Select] to set the digit. The editable digit will

move to the right automatically.

y Repeat r and t to input all allowable digits.

u Push [Call] or [PTT] to transmit the selected TX code.

TO EDIT A TX CODE VIA [TX CODE ENTER] KEY:

q Select the desired TX code channel via [TX Code CH Up]/[TX

Code CH Down].

w Push [TX Code Enter] to enter the TX code edit mode.

e Push [TX Code Enter] to select the desired digit to be edited.

r Set the desired digit using [ ]/[ ]/[TX Code CH Up]/[TX

Code CH Down].

t Push [TX Code Enter] to set the digit. The editable digit will move

to the right automatically.

y Repeat r and t to input all allowable digits.

u Push [Call] or [PTT] to transmit the selected TX code.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 16 (1,1)

CONVENTIONAL OPERATION

D DTMF transmission

If the transceiver has [DTMF Autodial] assigned to it, the automatic

DTMF transmission function is available. Up to 8 DTMF channels

are available.

TO SELECT A TX CODE:

q Push [DTMF Autodial]— a DTMF channel appears.

w Push [ ]/[ ] to select the desired DTMF channel.

e Push [DTMF Autodial] to transmit the DTMF code in the selected

DTMF channel.

■ Scrambler function

The voice scrambler function provides private communication be-

tween stations. The frequency inversion type is equipped to all ver-

sions, and some versions have the Rolling or Non-rolling type

installed.

q Push [Scrambler] to turn the scrambler function ON.

w “ ” appears.

e Push [Scrambler] again to turn the scrambler function OFF.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 17 (1,1)

CONVENTIONAL OPERATION

■ User set mode

User set mode is accessed at power ON and allows you to set

seldom-changed settings. In this case you can “customize” trans-

ceiver operation to suit your preferences and operating style.

Entering the user set mode:

q While pushing and holding [ ] and [ ], rotate [VOL] to enter

the user set mode at power ON.

w Push and hold [P0] to enter user set mode. Push [P0] momen-

tarily to select the item.

Then push [ ] and [ ] to set the desired level/condition.

Available set mode functions:

• Backlight : ON, Auto or OFF

• Beep : ON or OFF

• SQL Level : 0 to 255

• AF Min level : ON or OFF

• Mic Gain : 1 to 5

• Battery Voltage : ON or OFF

e Push and hold [P0] again to exit set mode.

User set mode is also available using a programmable key. Please

refer to p. 11 “User Set Mode” section.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 18 (1,1)

BIIS OPERATION

■ Default setting

The following functions are assigned to each programmable key as

the default. Ask your dealer for details.

[P0]; Call : Push to transmit a 5-tone/BIIS call when the

selected channel is a 5-tone or MSK channel,

respectively.

[P1]; Digital : Push to select the call list ID/transmit mes-

sage, or to display the receive message

record for selection.

[P3]; Moni(Audi) : Push this key after the communication to

send a “clear down” signal during MSK chan-

nel operation.

[ ]/[ ]; CH Down/Up

: While in the standby condition, selects the

operating channel.

After pushing [Digital] or [TX Code CH Se-

lect], push to select the call list or TX code

channel, respectively.

[P2]/[Red]; Null : No function is assigned.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 19 (1,1)

BIIS OPERATION

■ Receiving a call

Individual call

q When an individual call is received;

• Beeps sound.

• “ ” appears and the mute is released.

• The programmed text message (e.g.“ ”) and the calling

station ID (or text) is displayed alternately, depending on the set-

ting.

• “ ” appears or blinks depending on the setting.

w Push and hold [PTT], then speak into the microphone at a nor-

mal voice level.

• Transmit/Busy indicator lights red.

e Release [PTT] to return to receive.

• Transmit/Busy indicator lights green while receiving a signal.

r To finish the conversation, push [P3] (Moni(Audi)) to send the

“Clear down” signal.

• Either station can send a clear down signal.

• “ ” is displayed for 2 sec. (approx.).

• “ ” disappears and the transceiver returns to the standby condi-

tion.

Appears or blinksAppears

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 20 (1,1)

BIIS OPERATION

Group call

q When a group call is received;

• Beeps sound.

• “ ” appears and the mute is released.

• The programmed text message (e.g.“ ”) and the calling sta-

tion ID (or text) is displayed alternately, depending on the setting.

• “ ” appears or blinks depending on the setting.

w Push and hold [PTT], then speak into the microphone at a nor-

mal voice level.

NOTE: Only one station is permitted to speak.

• Transmit/Busy indicator lights red.

e Release [PTT] to return to receive.

• Transmit/Busy indicator lights green while receiving a signal.

r To finish the conversation, push [P3] (Moni(Audi)) to send the

“Clear down” signal.

• Either station can send a clear down signal.

• “ ” is displayed for 2 sec. (approx.)

• “ ” disappears and the transceiver returns to the standby condi-

tion.

Appears or blinksAppears

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 21 (1,1)

BIIS OPERATION

Displaying the received call record

— Queue indication

The transceiver memorizes the calling station IDs for record. Up to

3 calls can be memorized, and the oldest call record is erased

when a 4th call is received. However, once the transceiver is pow-

ered OFF, the all records are cleared.

q Push [P1] (Digital) for 1 sec.

• Displays following indication.

When a record is available

When no record is available

w Push [ ]/[ ] to select the desired call.

e Push [P1] (Digital) for 1 sec. again to return to the standby con-

dition.

• When no operation is performed for 30 sec., the transceiver returns

to the standby condition automatically.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 22 (1,1)

BIIS OPERATION

■ Transmitting a call

Total of a 3 ways for code selection are available—selecting the call

code from memory, entering the call code from the keypad and call-

ing back from the queue channel record.

Using call memory

q While in the standby condition, push [P1] (Digital) to enter the

call code memory channel selection mode.

w Push [ ]/[ ] to select the desired call code.

e Push [P0] (Call) or [PTT]* to call.

*PTT call can be made only when PTT call capability is permitted.

NOTE: When no answer back is received, the transceiver re-

peats the call 3 times (default) automatically, and

“”is

displayed during each call. However, an error beep sounds

and

“”

is displayed when no answer back is received

after the calls.

r Push [PTT] to transmit; release to receive.

t Push [P3] (Moni(Audi)) to send the “Clear down” signal.

Call code text is displayed.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 23 (1,1)

BIIS OPERATION

Calling back from the queue channel

q While in the standby condition, push [P1] (Digital) for 1 sec. to

enter queue memory channel selection mode.

w Push [ ]/[ ] to select the desired record.

e Push [P0] (Call) or [PTT]* to call.

*PTT call can be made only when PTT call capability is permitted.

NOTE: When no answer back is received, the transceiver re-

peats the call 3 times (default) automatically, and

“”is

displayed during each call. However, an error beep sounds

and

“”is displayed when no answer back is received

after the calls.

r Push [PTT] to transmit; release to receive.

t Push [P3] (Moni(Audi)) to send the “Clear down” signal.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 24 (1,1)

BIIS OPERATION

Direct code entry

q While in the standby condition, push [TX Code Enter] to enter

the TX code edit mode.

• Editable code digit blinks.

w Push [TX Code Enter] to select the desired digit to be edited.

• Editable digit differs according to the setting.

e Set the desired digit using [ ]/[ ]/[TX Code CH Up]/[TX

Code CH Down].

r Push [TX Code Enter] to set the digit. The editable digit will move

to the right automatically.

t Repeat e and r to input all allowable digits.

y Push [P0] (Call) or [PTT]* to call.

*PTT call can be made only when PTT call capability is permitted.

NOTE: When no answer back is received, the transceiver re-

peats the call 3 times (default) automatically, and

“”is

displayed during each call. However, an error beep sounds

and

“”is displayed when no answer back is received

after the calls.

u Push [PTT] to transmit; release to receive.

i Push [P3] (Moni(Audi)) to send the “Clear down” signal.

For your information

When the “UpDate” setting for the call code is enabled, the set code

is overwritten into the call code memory.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 25 (1,1)

BIIS OPERATION

■ Receiving a message

Receiving a status message

q When a status message is received;

• Beeps sound.

• The calling station ID (or text) and the status message is displayed

alternately, depending on the setting.

w Push [P3] (Moni(Audi)) to return to the standby condition.

NOTE: Only the calling station ID (or text) is displayed (no

message is displayed alternately) when the scroll timer is set

to “OFF”. In this case, push [Status Up]/[Status Down] to dis-

play the status message manually.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 26 (1,1)

BIIS OPERATION

Receiving an SDM

q When an SDM is received;

• Beeps sound.

• The calling station ID (or text) and the SDM is displayed alternately,

depending on the setting.

w When the received SDM includes more than 8 characters, the

message scrolls automatically, when the automatic scroll func-

tion is activated.

• Push [Status Up]/[Status Down] to scroll the message manually.

e Push [P3] (Moni(Audi)) to return to the standby condition.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 27 (1,1)

BIIS OPERATION

Received message selection

The transceiver memorizes the received messages for record. Up

to 6 messages for status and SDM, or 95 character SDM’s can be

memorized. The oldest message is erased when the 7th message

is received. However, once the transceiver is powered OFF, all

messages are cleared.

q Push [P1] (Digital) for 1 sec.

• Displays queue memory.

w Push [P1] (Digital) momentarily.

• Displays message memory.

When a message is available

When no message is available

e Push [ ]/[ ] to select the desired message.

• When selecting the SDM that includes more than 8 characters, the

message scrolls automatically, when the automatic scroll function is

activated.

• Push [Status Up]/[Status Down] to scroll the message manually.

r Push [P1] (Digital) for 1 sec. again to return to the standby con-

dition.

• When no operation is performed for 30 sec., the transceiver returns

to the standby condition automatically.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 28 (1,1)

BIIS OPERATION

■ Transmitting a status

General

The status message can be selected with the programmed text,

and the message text is also displayed on the function display of

the called station.

Up to 24 status types (1 to 24) are available, and the status mes-

sages 22 and 24 have designated meanings.

Status 22: Emergency*

Status 24: GPS request

*The status 22 can also be used as a normal status message by dis-

abling the designated meaning. However, the status 24 is ﬁxed.

The status call can be sent with both individual and group calls.

Transmitting a status

q While in the standby condition, push [P1] (Digital), then push

[ ]/[ ] to select the desired station/group code.

w Push [P1] (Digital) again, then push [ ]/[ ] to select the de-

sired status message.

Or, you can select the desired status message using [Status

Up]/[Status Down] key directly.

e Push [P0] (Call) or [PTT]* to transmit the status message to the

selected station/group.

*PTT call can be made only when PTT call capability is permitted.

• 2 beeps will sound and the transceiver returns to the standby con-

dition automatically when the transmission is successful.

Status message is displayed.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 29 (1,1)

BIIS OPERATION

■ Transmitting an SDM

General

The short data message, SDM, can be sent to an individual station

or group stations. Also, 8 SDM memory channels are available and

the messages can be edited via PC programming.

Transmitting an SDM

q While in the standby condition, push [P1] (Digital), then push

[ ]/[ ] to select the desired station/group code.

w Push [P1] (Digital) again, then push [ ]/[ ] to select the de-

sired SDM.

Or, you can select the desired SDM using [Status Up]/[Status

Down] key directly.

e Push [P0] (Call) or [PTT]* to transmit the SDM to the selected

station/group.

*PTT call can be made only when PTT call capability is permitted.

• 2 beeps will sound and the transceiver returns to the standby con-

dition automatically when the transmission is successful.

SDM is displayed.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 30 (1,1)

BIIS OPERATION

■ Position data transmission

When the optional OPC-966

INTERFACE CABLE

and a GPS receiver

is connected to the transceiver, the position (longitude and latitude)

data can be transmitted automatically.

Ask your dealer or system operator for connection details.

The position data is transmitted when;

• Status 24 message is received

*When the status 24 message, GPS request, is received.

• Fully automatic

When automatic position transmission is enabled, send the po-

sition data according to ‘Time Marker’ and ‘Interval Timer’ set-

tings.

• PTT is released

When ‘Send with Logoff’ is enabled.

- Set the “Log-In/Off” item as “L-OFF”.

• After sending a status message

When ‘Send with Status’ is enabled.

• After sending an SDM

When ‘Send with SDM’ is enabled.

• After sending status 22 (Emergency)

When ‘Send with Emergency’ is enabled.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 31 (1,1)

BIIS OPERATION

■ Printer connection

When the optional OPC-966

INTERFACE CABLE

is connected to the

transceiver, a printer can be connected to print out the received

SDM content and the ID of the station who sent the message.

Ask your dealer or system operator for connection details.

■ PC connection

When the optional OPC-966

INTERFACE CABLE

is connected to the

transceiver, a PC can be connected to provide remote control, data

reception, etc.

Ask your dealer or system operator for connection details.

■ Digital ANI

The own ID can be transmitted each time the PTT is pushed (log-in)

or released (log-off) during individual or group call communications.

By receiving the ANI, the communication log can be recorded when

using a PC dispatch application.

In addition, when using the ANI with log-in, the PTT side tone func-

tion can be used to inform you that the ID is sent and voice com-

munication can be performed.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 32 (1,1)

BIIS OPERATION

■ Auto emergency transmission

When [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is

pushed, an emergency signal is automatically transmitted for the

speciﬁed time period.

The status 22 (Emergency) is sent to the selected ID station, and

the position data is transmitted after the emergency signal when a

GPS receiver is connected to the transceiver.

The emergency transmission is performed on the emergency chan-

nel, however, when no emergency channel is speciﬁed, the signal is

transmitted on the previously selected channel.

There is no change in the function display or beep emission during

automatic emergency transmission.

■ Stun function

When the speciﬁed ID, set as a killer ID, is received, the stun func-

tion is activated.

When the killer ID is received, the transceiver switches to the pass-

code required condition. Entering of the passcode via the keypad is

necessary to operate the transceiver again in this case.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 33 (1,1)

BIIS OPERATION

■ BIIS indication

The following indications are available for the BIIS operation on an

MSK channel.

: Individual/group call is successful.

: Message (status or SDM) transmission is successful.

: No answer back is received.

: Appears during retry of the call (2nd call).

: End the communication.

: Operating channel is in the busy condition.

■ Priority A channel selection

When one of the following operations is performed, the transceiver

selects the Priority A channel automatically.

Priority A is selected when;

• Clear down signal is received/transmitted

- Set the “Move to PrioA CH” item as “Clear Down”.

• Turning the power ON

The Priority A channel is selected each time the transceiver

power is turned ON.

• Status call

The Priority A channel is selected when transmitting a status

call.

- Enable the “Send Status on PrioA CH” item in the MSK con-

ﬁguration.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 34 (1,1)

BATTERY CHARGING

■ Battery charging

Prior to using the transceiver for the ﬁrst time, the battery pack must

be fully charged for optimum life and operation.

CAUTION: To avoid damage to the transceiver, turn it OFF while

charging.

• Recommended temperature range for charging:

+10°C to +40°C

- The Li-Ion battery functions within –20°C to +60°C

• Use the specified chargers (BC-152, BC-119N and BC-121N).

NEVER use another manufacturer’s charger.

• Use the optional AC adapter (BC-147E) for the BC-152.

• NEVER use another manufacturer’s AC adapter.

Recommendation:

Charge the supplied battery pack for a maximum of up to

10 hours. Li-Ion batteries are different from Ni-Cd batteries in that

it is not necessary to completely charge and discharge them to

prolong the battery life. Therefore, charging the battery in inter-

vals, and not for extended periods is recommended.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 35 (1,1)

BATTERY CHARGING

■ Caution

CAUTION! NEVER insert the battery pack/transceiver (with the

battery pack attached) with wet or soiled into the charger. This may

result in corrosion of the charger terminals or damage to the

charger. The charger is not waterproof and water can easily get into

it.

NEVER incinerate used battery packs. Internal battery gas may

cause an explosion.

NEVER immerse the battery pack in water. If the battery pack be-

comes wet, be sure to wipe it dry immediately (particularly the bat-

tery terminals) BEFORE attaching it to the transceiver. Otherwise,

the terminals will become corroded, or cause connection failure,

etc.

NEVER short the terminals of the battery pack. Also, current may

ﬂow into nearby metal objects, such as a necklace, etc. Therefore,

be careful when carrying with, or placing near metal objects, carry-

ing in handbags, etc.

AVOID leaving the battery pack in a fully charged, or completely

discharged condition for long time. It causes shorter battery life. In

case of leaving the battery pack unused for a long time, it must be

kept safely after discharge, or use the battery until the battery indi-

cator appears, then remove it from the transceiver.

If your battery pack seems to have no capacity even after being

charged, fully charge the battery pack again. If the battery pack still

does not retain a charge (or very little), a new battery pack must be

purchased.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 36 (1,1)

BATTERY CHARGING

■ Optional battery chargers

ï Regular charging with the BC-152

q Attach the BC-152 to a ﬂat surface, such as a desk, if desired.

w Connect the AC adapter (BC-147E) as shown below.

e Insert the battery pack with/without the transceiver into the

charger.

• The charge indicator lights green.

r Charge the battery pack approx. 9–10 hours, depending on the

remaining power condition.

• The charge indicator goes off when charging is complete.

Charge indica-

tor lights green

while charging.

BC-152

Supplied screws

Ensure sides of the

battery pack are cor-

rectly aligned with

the charger groves.

AC adapter;

BC-147E

(Purchase

separately)

Battery pack

Transceiver

Turn power OFF

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 37 (1,1)

BATTERY CHARGING

D For your convenience

Eyelet

USE a rubber band to

secure the transceiv-

er while charging, if

desired.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 38 (1,1)

BATTERY CHARGING

ï AD-100 installation

q Install the AD-100 desktop charger adapter into the holder space

of the BC-119N/121N.

Desktop charger adapter

Connectors

Plugs

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 39 (1,1)

BATTERY CHARGING

w Connect the plugs of the BC-119N/121N to the AD-100 with the

connector, then install the adapter into the charger with the sup-

plied screws.

Screws supplied with

the charger adapter

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 40 (1,1)

BATTERY CHARGING

D Rapid charging with the BC-119N+AD-100

The optional BC-119N provides rapid charging of Li-Ion battery

pack.

The following are additionally required:

• One AD-100

(purchase separately)

• An AC adapter (may be supplied with BC-119N depending on ver-

sion) or the DC power cable (OPC-515L/CP-17L).

AC adapter

(Not supplied with

some versions.)

AD-100 charger

adapter is instal-

led in BC-119N.

Optional OPC-515L (for 13.8 V

power source) or CP-17L (for

12 V cigarette lighter socket)

can be used instead of the AC

adapter.

Battery pack

Transceiver

Turn power OFF

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 41 (1,1)

BATTERY CHARGING

D Rapid charging with the BC-121N+AD-100

The optional BC-121N allows up to 6 battery packs to be charged

simultaneously. The following are additionally required.

• Six AD-100

(purchase separately)

• An AC adapter (BC-157) or the DC power cable (OPC-656)

AC adapter

(Purchase

separately)

MULTI-CHARGER

DC power cable (OPC-656)

Connect with the DC power supply;

13.8 V/7 A minimum

AD-100 charger

adapters are installed

in each slot.

Battery pack

Transceiver

Turn power OFF

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 42 (1,1)

BATTERY CHARGING

■ Optional battery case

When using the optional battery case attached to the transceiver,

install 5 × AA (R6) size alkaline batteries as illustrated at right. The

BP-226 meets JIS waterproof speciﬁcation grade 4.

q Hook your ﬁnger under the latch, and open the cover in the direc-

tion of the arrow (q). (Fig.1)

w Then, install 5 × AA (R6) size alkaline batteries. (Fig.2)

• Install the alkaline batteries only.

• Be sure to observe the correct polarity.

• Do not pin the ribbon under the batteries.

e Close the cover by ﬁtting in the direction of the arrow (w) ﬁrst,

then check the latch is in place (e). (Fig.1)

• Be sure the gasket and the ribbon are set correctly, and do not pro-

trude from the battery case. (Fig.3)

CAUTION:

• When installing batteries, make sure they are all the same

brand, type and capacity. Also, do not mix new and old batter-

ies together.

• Keep battery contacts clean. It’s a good idea to clean battery

terminals once a week.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 43 (1,1)

BATTERY CHARGING

BP-226

Latch

Fig.1

Fig.2

Ribbon

Fig.3

Gasket

Ribbon

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 44 (1,1)

SPEAKER-MICROPHONE

■ Optional HM-138 description

NEVER immerse the connector in water. If the connector becomes

wet, be sure to dry it BEFORE attaching it to the transceiver.

NOTE: The microphone is located at the top of the speaker-mi-

crophone, as shown in the diagram above. To maximize the

readability of your transmitted signal (voice), hold the micro-

phone approx. 5 to 10 cm from your mouth, and speak in a nor-

mal voice level.

Alligator type clip

To attach the speaker-mic.

to your shirt or collar, etc.

PTT switch

Transmits while pushed

Receives while released

Microphone

Speaker

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 45 (1,1)

SPEAKER-MICROPHONE

■ Attachment

Attach the connector of the speaker-microphone into the [SP MIC]

connector on the transceiver and tighten the screw.

IMPORTANT: KEEP the [SP MIC] jack cover attached (trans-

ceiver) when the speaker-microphone is not in use. Water will

not get into the transceiver even if the cover is not attached,

however, the terminals (pins) will become rusty, or the trans-

ceiver will function abnormally if the connector becomes wet.

CAUTION: Attach the

speaker-microphone s

connector securely to pre-

vent accidental dropping,

or water intrusion in the

connector.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 46 (1,1)

OPTIONS

• BP-226

BATTERY CASE

Battery case for 5 × AA (R6) alkaline cells.

• BP-227

BATTERY PACK

7.2 V/1700 mAh Li-Ion battery pack. The same as supplied with

the transceiver. BP-227 must be charged with the optional BC-152

or the BC-119N/121N.

BP-226 BP-227

• BC-152

DESKTOP CHARGER

+ BC-147E

AC ADAPTER

Used for regular charging of the battery

pack. The AC adapter, BC-147E, must

be purchased separately.

Charging time: approx. 9–10 hours

• BC-119N

DESKTOP CHARGER

+ AD-100

CHARGER ADAPTER

+ BC-145

AC ADAPTER

For rapid charging of battery packs. An

AC adapter is not supplied with some

versions.

Charging time: approx. 2 to 2.5 hours

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 47 (1,1)

OPTIONS

• BC-121N

MULTI

CHARGER

+ AD-100

CHARGER ADAPTER

(6 pcs.)

+ BC-157

AC ADAPTER

For rapid charging of up to 6

battery packs (six AD-100’s are

required) simultaneously. An

AC adapter should be pur-

chased separately. Charging

time: approx. 2 to 2.5 hours.

• HM-138

SPEAKER

MICROPHONE

Full-sized waterproof (JIS

grade 7; 1m/30 min.) speaker-

microphone including alligator

type clip to attach to your shirt

or collar, etc.

• OPC-966

INTERFACE CABLE

Provides advanced operation, such as printer, GPS connection for

position data transmission capabilities during BIIS operation.

• FA-S24V/FA-S59V

FLEXIBLE ANTENNAS

FA-S24V: 136–150 MHz FA-S59V: 150–174 MHz

• FA-S62VS/FA-S63VS/FA-S57US

STUBBY ANTENNAS

FA-S62VS: 150–162 MHz FA-S63VS: 160–174 MHz

FA-S57US: 450–490 MHz

Some options may not available in some countries. Please ask your

dealer for details.

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 48 (1,1)

DOC

CE versions of the IC-F51/F61 which display the

“CE” symbol on the serial number seal, comply with

the essential requirements of the European Radio

and Telecommunication Terminal Directive

1999/5/EC.

DECLARATION

OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku

Osaka 547-0003, Japan

Kind of equipment:

VHF TRANSCEIVER

Type-designation: iC-

f51

Signature

Authorized representative name

Place and date of issue

Düsseldorf 3rd Sep. 2003

Declare on our sole responsibility that this equipment complies with the

essential requirements of the Radio and Telecommunications Terminal

Equipment Directive, 1999/5/EC, and that any applicable Essential Test

Suite measurements have been performed.

Version (where applicable):

0168

136 174 MHz 12.5 kHz/20 kHz/25 kHz

This compliance is based on conformity with the following harmonised

standards, specifications or documents:

i) EN 301 489-1 v1.3.1 (Sept 2001)

ii) EN 301 489-5 (August 2000)

iii) EN 60950 (August 1992+A11)

iv) EN 300 086-2 (March 2001)

v) EN 300 219-2 (March 2001)

vi) EN 300 113-2 (March 2001)

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 49 (1,1)

DOC

This warning symbol indicates that this equipment op-

erates in non-harmonised frequency bands and/or may

be subject to licensing conditions in the country of use.

Be sure to check that you have the correct version of

this radio or the correct programming of this radio, to

comply with national licensing requirement.

DECLARATION

OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku

Osaka 547-0003, Japan

Kind of equipment:

UHF TRANSCEIVER

Type-designation: iC-

f61

Signature

Authorized representative name

Place and date of issue

Düsseldorf 3rd Oct. 2003

Declare on our sole responsibility that this equipment complies with the

essential requirements of the Radio and Telecommunications Terminal

Equipment Directive, 1999/5/EC, and that any applicable Essential Test

Suite measurements have been performed.

Version (where applicable):

0168

400 470 MHz 12.5 kHz/20 kHz/25 kHz

This compliance is based on conformity with the following harmonised

standards, specifications or documents:

i) EN 301 489-1 v1.3.1 (Sept 2001)

ii) EN 301 489-5 (August 2000)

iii) EN 60950 (August 1992+A11)

iv) EN 300 086-2 (March 2001)

v) EN 300 219-2 (March 2001)

vi) EN 300 113-2 (March 2001)

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 50 (1,1)

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

A-6295H-1EU-e

Printed in Japan

< Intended Country of Use >

GER

AUT

GBR

IRL

NOR

FRA

NED

BEL

LUX

ESP

POR

ITA

GRE

SWE

DEN

FIN

SUI

IC-F51_F61 BIIS-3.qxd 06.3.24 1:45 PM Page 51 (1,1)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-F51 F61 in the language / languages: English as an attachment in your email.

The manual is 0,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Icom IC-F51 F61 Manual

Product: