670162
29
Zoom out
Zoom in
Previous page
1/180
Next page
Transverter jack information
When 2 to 13.8 V is applied to pin 6 of [ACC 2], the
[X-VERTER] connector is activated for transverter op-
eration and the antenna connectors do not receive or
transmit any signals.
While receiving, the [X-VERTER] connector can be
activated as an input terminal from an external trans-
verter.
While transmitting, the [X-VERTER] connector out-
puts signals of the displayed frequency at 20 dBm
(22 mV) as signals for the external transverter.
FSK and AFSK (SSTV) connections
To connect a TNC or scan converter, etc., refer to the diagram below.
D FSK operation— when connecting to [ACC 1]
D AFSK operation
D When connecting to the [USB] connector
Connect a USB cable (third party’s) between the transceiver’s USB connector [USB] (B) on the rear panel and
the PC. (p. 19)
Icom HP (http://www.icom.co.jp/world/support/index.html) gives the USB driver and the installation guide download service.
Transverter connector
PC
RS-232C
TNC or scan converter
When using a PC application
When using a TNC
1
2
3
4
5
6
7
8
Rear panel view
Rear panel view
RTTY
GND
AF
SEND
RTTY
GND
AF
SEND
RTTY OUTPUT
GND
AUDIO INPUT
PTT
RTTY OUTPUT
GND
AUDIO INPUT
PTT
1
2
3
4
5
6
7
8
Connect to serial port, parallel
port, speaker jack, microphone
jack and line IN/OUT jack, etc.
See the instruction manual of the
application for details.
Connect to serial port, parallel
port, speaker jack, microphone
jack and line IN/OUT jack, etc.
See the instruction manual of
the application for details.
When connecting to [ACC 1]
When connecting to [MIC]
When using a PC application
When using a TNC
PC
RS-232C
TNC or scan converter
PTT
Audio output
AF input
GND
AFSK output
AF input
GND
PTT*
SQL input
*When using the VOX function, no need to connect. Refer to the instruction
manual of the external equipment (TNC, etc.).
When connecting the squelch line, consult the necessary manual (TNC, etc.).
q
w
e
r
t
y
u
i
1
2
3
4
5
6
7
8
z
z
x
x
c
c
v
v*
z
x
c
v
z
x
c
v
b
b
n
n
b
n
Rear panel view
Front panel view
22
2
INSTALLATION AND CONNECTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7600 in the language / languages: English as an attachment in your email.

The manual is 14,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info