670162
15
Zoom out
Zoom in
Previous page
1/180
Next page
#9 PASSBAND TUNING CONTROLS [TWIN-PBT]
(p. 75)
Adjusts the receiver’s IF filter passband width via
the DSP.
Passband width and shift frequency are displayed in
the multi-function display.
Push and hold [PBT-CLR] for 1 sec. to clear the PBT
sett
ings.
Adjustment range is set to half of the IF filter passband
width. 25 Hz steps and 100 Hz steps are available.
What is the PBT control?
The PBT function electronically modifies the IF pass-
band width to reject interference. This transceiver uses
the DSP circuit for the PBT function.
PBT2
PBT1
+
Low cutHigh cut Center
$0 PBT CLEAR SWITCH [PBT-CLR] (p. 75)
Push and hold for 1 sec. to clear the PBT settings.
The indicator on this switch lights green when PBT is in
use.
$1 NOTCH SWITCH [NOTCH] (p. 83)
Switches the notch function between auto, man-
ual and OFF in SSB and AM modes.
Either auto or manual notch function can be deacti-
vated in others set mode. (p. 132)
Turns the manual notch function ON and OFF
when pushed in CW, RTTY and PSK mode.
Turns the auto notch function ON and OFF
when pushed in FM mode.
• “ appears when manual notch is in use.
• “
appears when auto notch is in use.
No indicator appears when the notch function is not
in use.
Push and hold for 1 sec. to switch the manual
notch characteristics from wide, middle and nar-
row when manual notch function is activated.
The indicator on this switch lights green when the
function is activated.
What is the notch function?
The notch function is a narrow filter that eliminates un-
wanted CW or AM carrier tones while preserving the de-
s
ired voice signal. The DSP circuit automatically adjusts
the notch frequency to effectively eliminate unwanted
tones.
$2 TX SWITCH [TX] (p. 87)
Push to turn the TX function ON and OFF.
Use [RIT/TX] control to vary the TX frequency.
Push and hold for 1 sec. to add the TX shift
frequency to the operating frequency.
What is the TX function?
TX shifts the transmit frequency without shifting the re-
ceive frequency. This is useful for simple split frequency
operation in CW, etc.
$3 CLEAR SWITCH [CLEAR] (pgs. 73, 87)
Push or push and hold for 1 sec.* to clear the RIT/
TX shift frequency.
* Depending on the quick RIT/TX clear function setting
(p. 132).
$4 TRANSMIT FREQUENCY CHECK SWITCH
[XFC]
Monitors the transmit frequency (including TX
frequency offset)
when pushed and held during
split frequency operation. (p. 88)
While pushing and holding this switch, the transmit
frequency can be changed with the main dial, key-
pad, memo pad or []/[] s
witches.
When the split lock function is turned ON, pushing
[XFC] cancels the dial lock function. (pgs. 88, 129)
Monitors the operating frequency directly
when pushed and held when the RIT function
is turned ON. (RIT is temporarily cancelled.)
(p. 73)
$5
MAIN/SUB•M.SCOPE SWITCH
[MAIN/SUB M.SCOPE]
Push to select access to the main or sub read-
out. (p. 26)
The selected readout frequency is displayed clearly.
The sub readout functions only during split operation
or dualwatch.
Push and hold for 1 sec. to turn the mini spec-
trum scope screen indication ON and OFF.
(p. 67)
The mini spectrum scope screen can be indicated
with another screen, such as memory, set mode
screen, simultaneously.
8
1
PANEL DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7600 in the language / languages: English as an attachment in your email.

The manual is 14,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info