670162
11
Zoom out
Zoom in
Previous page
1/180
Next page
MF3 (MULTI-FUNCTION 3 SWITCH)
P.AMP SWITCH (P.AMP) (p. 72)
Selects one of 2 receive RF preamps
or bypasses them.
• “P. AMP1” activates 10 dB preamp.
• “ P. AMP2” activates 16 dB high-gain pre-
amp.
• “P. AMP OFF” can also be selected.
Turns the preamp function OFF when
pushed and held for 1 sec.
What is the preamp?
T
he preamp amplifies signals in the front end to
improve S/N ratio and sensitivity. Select “P. AMP1”
or “P. AMP2” when receiving weak signals.
MF4 (MULTI-FUNCTION 4 SWITCH)
ATT SWITCH (ATT) (p
. 72)
Selects 6 dB, 12 dB or 18 dB attenua-
tor when pushed.
• “ATT OFF” can also be selected.
Turns the attenuator function OFF
when pushed and held for 1 sec.
What is the attenuator?
T
he attenuator prevents a desired signal from
being distorted when very strong signals are near
the desired frequency, or when very strong electro-
m
agnetic fields, such as from a broadcasting sta-
tion, are near your location.
MF5 (MULTI-FUNCTION 5 SWITCH)
AGC SWITCH (AGC) (p. 74)
Activates and selects fast, middle
or slow AGC time constant when
pushed.
In FM mode, only “FAST” is available.
Enters the AGC set mode when
pushed and held for 1 sec.
AGC time constant can be set be-
tween 0.1 to 8.0 sec. (depends on
mode)
, or turned OFF. When AGC is
“OFF, the S-meter does not function.
What is the AGC?
T
he AGC controls receiver gain to produce a con-
s
tant audio output level, even when the received
signal strength varies dramatically. Select “FAST”
for tuning and then select MIDor SLOWde-
pending on the receiving condition.
MF6 (MULTI-FUNCTION 6 SWITCH)
VOX SWITCH (VOX) (p. 84)
Push to turn the VOX function ON and
OFF during SSB, AM and FM mode
operation.
Push and hold for 1 sec. to enter VOX
set mode.
What is the VOX function?
T
he VOX function (voice operated transmission)
activates transmission without pushing the trans-
mit
switch or PTT switch when you speak into the
microphone; then automatically returns to receive
when you stop speaking.
BK-IN SWITCH (BK-IN) (p. 85)
Selects semi break-in, full break-in
operation, or turns the break-in opera-
tion OFF when pushed in CW mode.
What is the break-in function?
T
he break-in function switches transmit and re-
ce
ive with CW keying. Full break-in function (QSK)
can monitor the receive signal during keying.
MF7 (MULTI-FUNCTION 7 SWITCH)
COMP SWITCH (COMP) (p. 86)
Turns the speech compressor ON and
OFF in SSB mode.
Switches the narrow, middle or wide
compression when pushed and held
for 1 sec.
What is the speech compressor?
The speech compressor compresses the trans-
mit
ter audio input to increase the average audio
output level, to increase talk power. This function is
effective for long-distance communication or when
propagation conditions are poor.
1
4
SWITCH (
1
4
) (p. 30)
Turns the
1
4 speed tuning function
ON and OFF in SSB data, CW, RTTY
and PSK modes.
1
4 function sets dial rotation to
1
4 of
normal speed for fine tuning.
TONE SWITCH (TONE) (pgs. 62, 63)
Switches between the tone encoder,
tone squelch function and no-tone op-
eration when pushed in FM mode.
Enters the tone set mode when
pushed and held for 1 sec. in FM
mode.
4
1
PANEL DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7600 in the language / languages: English as an attachment in your email.

The manual is 14,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info